05-17-2007
EMC Powerpath
hdiskpower are the EMC powerpath pseudo devices. If you're see hdiskpower on a system then run the command "powermt display dev=all". The result will be a long display showing the relationship between hdisk dvices and hdiskpower devices.
7 More Discussions You Might Find Interesting
1. IP Networking
HI folks. I am developing a protocol and I need to bind to an IP address that is not configured to my machine. The problem is with bind(). The sysctl system call seamed to overcome the problem of bind if you set the proc/sys/net/ipv4/ip_nonlocal_bind flag. Although I tryed to set the flag either... (7 Replies)
Discussion started by: developer
7 Replies
2. UNIX for Dummies Questions & Answers
I am a new Unix user looking for ways, other than time, to become an effective unix administrator. All sugestions welcome.
Thanks (10 Replies)
Discussion started by: dtooth71
10 Replies
3. UNIX for Dummies Questions & Answers
Hai, friends.
In one exam which i have to attend in the month of january, they asked "knowledge of c and unix are required" .
I am beginner to unix, even i dont know from where to start .
Please suggest me what to do , to get through the exam and interview.
I have already downloaded... (2 Replies)
Discussion started by: nani_ynm
2 Replies
4. Shell Programming and Scripting
Can somebody explain me the following part within a awk command:
awk '{for(i=1;i<=NF;i++) if ($i=="mm")c++}
Can somebody please explain me the part (i=1;i<=NF;i++) ????:D:D:D:D (1 Reply)
Discussion started by: RubinPat
1 Replies
5. Linux
Blitz PHP
I am having trouble installing Blitz PHP blitz-0.6.10.tar.gz
Here is what i did:
cd /tmp
wget blitz-0.6.10.tar.gz
tar zxfv blitz-0.6.10.tar.gz
cd blitz-0.6.10
And then I tried
./configure
Output: -bash: No such file in directory
make
Output: No targets in the... (1 Reply)
Discussion started by: kendel
1 Replies
6. Shell Programming and Scripting
Hi Friends,
I know very well the basic commands of Unix but i want to concentrate on unix shell programming can you please how to learn and suggest me how to become comfortable level.
Thanks in advance (1 Reply)
Discussion started by: victory
1 Replies
7. UNIX for Dummies Questions & Answers
So I have a Networking class at my university that involves learning the basic commands of unix (i.e. Chmod, cat, cp, ls, mv, rm, mkdir, rmdir, pwd, etc) and my professor had us download and install Solaris and PuTTY as a means of...I suppose practicing using/executing commands. However due to... (7 Replies)
Discussion started by: bo74
7 Replies
LEARN ABOUT REDHAT
pnmpsnr
pnmpsnr(1) General Commands Manual pnmpsnr(1)
NAME
pnmpsnr - compute the difference between two images (the PSNR)
SYNOPSIS
pnmpsnr [pnmfile1] [pnmfile2]
DESCRIPTION
Reads two PBM, PGM, or PPM files, or PAM equivalents, as input. Prints the peak signal-to-noise ratio (PSNR) difference between the two
images. This metric is typically used in image compression papers to rate the distortion between original and decoded image.
If the inputs are PBM or PGM, pnmpsnr prints the PSNR of the luminance only. Otherwise, it prints the separate PSNRs of the luminance, and
chrominance (Cb and Cr) components of the colors.
The PSNR of a given component is the ratio of the mean square difference of the component for the two images to the maximum mean square
difference that can exist betwee any two images. It is expressed as a decibel value.
The mean square difference of a component for two images is the mean square difference of the component value, comparing each pixel with
the pixel in the same position of the other image. For the purposes of this computation, components are normalized to the scale [0..1].
The maximum mean square difference is identically 1.
So the higher the PSNR, the closer the images are. A luminance PSNR of 20 means the mean square difference of the luminances of the pixels
is 100 times less than the maximum possible difference, i.e. 0.01.
SEE ALSO
pnm(5)
04 March 2001 pnmpsnr(1)