04-11-2007
Configuring 1 Nic card with 2 IP addresses and 2 seperate default Gateways in Solaris
Hi ......
I'm trying to configure my Solaris servers with only one NIC card to have 2 IP addresses as well as 2 different default gateways.
( NOT to be confused with multi-pathing - with 2 physical IPs & 1 virtual ip)
Thanks,
Remi
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Discussion started by: cyno
2 Replies
2. HP-UX
Hi.
I have HP-9000 Server running HP-UX 10.20. rECENTLY OUR network upgraded to 100mb/sec and I want to do same on the server. So, I add the second Network card (100MB). But the problem is, I can't find a way of configuring this card. How am i going to tell the server to use this 100mb card... (1 Reply)
Discussion started by: wobitu
1 Replies
3. HP-UX
using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies
4. Solaris
Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0:... (3 Replies)
Discussion started by: pray44u
3 Replies
5. IP Networking
Old DG box Aviion PentiumPro running R4.20Mu06 being used to try to recreate Ingres db from backup tapes so machine has not been operational before and some of original files in /etc may have ben overwritten
Unable to get NIC working
Any pointers on how to go about configuring NIC :rolleyes: (0 Replies)
Discussion started by: lindab
0 Replies
6. Shell Programming and Scripting
Hi,
I want to configure 2-gateways in Linux .
Please tell me how I can achieve this. I am accesing 2-internet
connection through these 2-gateways. So I am looking that
if 1-gets down then also other one is working.
Regards
JAGDISH (1 Reply)
Discussion started by: jagdish.machhi@
1 Replies
7. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
8. Solaris
Hi All,
I am unable to detect NIC card in solaris 10 installed on X86 system after installation, every thing is installed properly, i have check bios settings in which it is detectable.
I suspect we have selected NETWORKED option as NO during installation.How to conform whether we have selected... (6 Replies)
Discussion started by: ravijanjanam12
6 Replies
9. UNIX for Beginners Questions & Answers
I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only.
... (1 Reply)
Discussion started by: alphatron150
1 Replies
PHYS(2) System Calls Manual PHYS(2)
NAME
phys - allow a process to access physical addresses
SYNOPSIS
phys(segreg, size, physadr)
DESCRIPTION
The argument segreg specifies a process virtual (data-space) address range of 8K bytes starting at virtual address segregx8K bytes. This
address range is mapped into physical address physadrx64 bytes. Only the first sizex64 bytes of this mapping is addressable. If size is
zero, any previous mapping of this virtual address range is nullified. For example, the call
phys(6, 1, 0177775);
will map virtual addresses 0160000-0160077 into physical addresses 017777500-017777577. In particular, virtual address 0160060 is the
PDP-11 console located at physical address 017777560.
This call may only be executed by the super-user.
SEE ALSO
PDP-11 segmentation hardware
DIAGNOSTICS
The function value zero is returned if the physical mapping is in effect. The value -1 is returned if not super-user, if segreg is not in
the range 0-7, if size is not in the range 0-127, or if the specified segreg is already used for other than a previous call to phys.
BUGS
This system call is obviously very machine dependent and very dangerous. This system call is not considered a permanent part of the sys-
tem.
ASSEMBLER
(phys = 52.)
sys phys; segreg; size; physadr
PDP11 PHYS(2)