04-07-2007
actually I wanted to know what is the code in UNIX for checking Network Interface Card's Physical Address?
8 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
All,
I have a need to software change the MAC address of a NIC in a Sparc Ultra 10 - I believe there is a command that allows to do this at boot up?
Is it a missing (to me) part of ifconfig ?
If so, what is the syntax?
All replies gratefully received !
Thanks
Andrew (3 Replies)
Discussion started by: wretch
3 Replies
2. IP Networking
I have a SCO OpenServer 5.0.5 and my cuestion is can i have 2 ip address in one nic?, how?.
Thanks. (1 Reply)
Discussion started by: dvl
1 Replies
3. IP Networking
Hi,
I bound a virtual IP to a network card on my E450 server and I am getting this error when I reboot the server, saying, " retrying host, RPC time out. I had to break this sequence and allow other services to load. Of course they didn't load properly. Please how can I sort this out? I do need... (8 Replies)
Discussion started by: Ronny
8 Replies
4. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
5. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
6. Windows & DOS: Issues & Discussions
Anyone ever see the NIC get a mac of 00-00-00-00-00-00?
Changing it in driver advanced tab didn't stick. Used macshift and gave it a random one. Best guess I had is it lost its eprom. It was an issues on my dads pc I stopped by after work so I wasn't able to boot a proper OS to further diagnose.
... (0 Replies)
Discussion started by: neutronscott
0 Replies
7. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
8. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT NETBSD
pccard
PCCARD(4) BSD Kernel Interfaces Manual PCCARD(4)
NAME
pccard -- PC Card bus driver
SYNOPSIS
device pccard
DESCRIPTION
The pccard driver implements the PC Card bus. The pccard driver supports all PC Card bridges in the system.
TUNABLES
The driver supports the following tunable parameters, which may be added to /boot/loader.conf or set via the sysctl(8) command:
hw.pccard.debug Non-zero values cause more verbose information to be printed when a 16-bit PC Card is inserted or removed.
hw.pccard.cis_debug Non-zero value causes the CIS parsing of the 16-bit PC Card to be much more verbose and include a complete CIS dump.
FILES
/dev/pccard0.cis This exclusive-use device will report all the CIS chains present in a PC Card, if a 16-bit PC Card is inserted in the slot.
Only one user at a time may access the CIS. The CIS is presented as the relevant byte stream from the PC Card. For CIS
tuples in Attribute Memory (the default), only the even locations are presented (the ODD locations are undefined per the
standard). For CIS tuples in Common Memory, every byte is presented to the user. Decoding of the CIS tuples is done via a
userland program. All tuples are presented to the user.
SEE ALSO
cardbus(4), pccbb(4)
PC Card Standard, Release 8.
BSD
July 9, 2002 BSD