Sponsored Content
Full Discussion: Link Aggregation
Operating Systems Solaris Link Aggregation Post 302113348 by Perderabo on Thursday 5th of April 2007 09:11:34 AM
Old 04-05-2007
I have never tried that, but I would expect it work. The adjective "separate" would not apply to trunked switches. If you try it, let us know if it works and which protocol was used to trunk the switches.
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Link Aggregation and LACP

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

2. Solaris

Difference between IPMP and Link Aggregation ?

Hi everybody, One client asked me to configure network failover and load balancing for two Ethernet interfaces, I tried IPMP but I was unable to do so, because he's using his Gateway as firewall and PING is disabled. so IPMP kept telling me that all interfaces failed because gateway can't be... (8 Replies)
Discussion started by: Sun Fire
8 Replies

3. IP Networking

bonding without switch link aggregation

I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies

4. AIX

Link aggregation with hacmp ?

Hi, I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies

5. HP-UX

Link Aggregation HPUX

Hi, Hoping someone can offer some advice on something i have not dealt with before. We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies

6. Solaris

Link aggregation

Me again :) I'm trying to find a page describing the L2, L3 und L4 modes of dladm. It's nice to read "hashed by ip header", but how should I use that? On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies

7. HP-UX

Break Link Aggregation in HP UX.

Hi, I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900. Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server. So It need to change in cluster script. But I dont know where I have to change it. Please... (1 Reply)
Discussion started by: mkiron
1 Replies

8. Solaris

Link Aggregation without LACP

Hi, I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP? I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies

9. IP Networking

Link Aggregation

Hi ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ? are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies

10. Solaris

How can I test link aggregation?

Hi, I have Solaris-10 server and link aggregation is configured on this in below way # dladm show-aggr key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto) device address speed duplex link state bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
merge(1)						      General Commands Manual							  merge(1)

NAME
merge - three-way file merge SYNOPSIS
file1 file2 file3 DESCRIPTION
combines two files that are revisions of a single original file. The original file is file2, and the revised files are file1 and file3. identifies all changes that lead from file2 to file3 and from file2 to file1, then deposits the merged text into file1. If the option is used, the result goes to standard output instead of file1. An overlap occurs if both file1 and file3 have changes in the same place. prints how many overlaps occurred, and includes both alterna- tives in the result. The alternatives are delimited as follows: lines in file1 lines in file3 If there are overlaps, edit the result in file1 and delete one of the alternatives. This command is particularly useful for revision control, especially if file1 and file3 are the ends of two branches that have file2 as a common ancestor. EXAMPLES
A typical use for is as follows: 1. To merge an RCS branch into the trunk, first check out the three different versions from RCS (see co(1)) and rename them for their revision numbers: 5.2, 5.11, and 5.2.3.3. File 5.2.3.3 is the end of an RCS branch that split off the trunk at file 5.2. 2. For this example, assume file 5.11 is the latest version on the trunk, and is also a revision of the "original" file, 5.2. Merge the branch into the trunk with the command: 3. File 5.11 now contains all changes made on the branch and the trunk, and has markings in the file to show all overlapping changes. 4. Edit file 5.11 to correct the overlaps, then use the command to check the file back in (see ci(1)). WARNINGS
uses the ed(1) system editor. Therefore, the file size limits of ed(1) apply to AUTHOR
was developed by Walter F. Tichy. SEE ALSO
diff3(1), diff(1), rcsmerge(1), co(1). merge(1)
All times are GMT -4. The time now is 07:31 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy