02-22-2007
Network minimal configuration and startup
Hi,
I have a LPAR running AIX 5.3 with multiple Etherchannels running (e.g. ent10-ent14 etc).
The person who configured up the interfaces set more that one interface through minimal config and startup under smitty->tcpip
When I try and clear out the IP address for one of the additional interfaces smit complains that the IP address is invalid because it is blank. How do I remove the additional IP addresses to leave only one primary interface?
I will configure up the addidtional IPs using smitty->tcpip-> additional configuration.
TIA
9 More Discussions You Might Find Interesting
1. HP-UX
Hi,
I have installed a HP-UX B.11.00 U 9000/800 Server in one of the domain. And I'm also able to telnet/ping into this server from systems in the same domain.
But I'm not able to telnet/ping into this server from a different domain.
So, what shoud need to do to achieve this... (6 Replies)
Discussion started by: S.Vishwanath
6 Replies
2. Solaris
hi again...
i configured my network settings sometiime ago using the sys-unconfig command.the active link was rtls0.
there was some problem with the network so i changed the ISP. now when im trying to reconfigure the system wit sys-unconfig, it tries to configure the network on rtls1 (and shows... (1 Reply)
Discussion started by: strider
1 Replies
3. Solaris
Can someone please point me in the correct direction of where I configure the network information on SunOS 5.8 server? (Searching SunSolve and Google have resulted in thousands of fixes for potential errors, but I can't find the general instructions, etc. for starting the process).
Thanks! (2 Replies)
Discussion started by: FredSmith
2 Replies
4. Slackware
I recently installed slackware 11 and have been very happy with it until I found out that some gnome related apps can cause gnome's network manager to alter the rc.init1 script by adding 3 lines to the script containing only the command, eth_up. This causes the script not to run properly and not... (1 Reply)
Discussion started by: djtrippin
1 Replies
5. UNIX for Dummies Questions & Answers
I need to know what commands I will need to use to change a host name, IP Address, and network configurations (routerings, dns, etc) and a Unix SCO machine.
Also, if there is any short tutorials on using the commands, i would defiently like that information.
Thanks!!! (1 Reply)
Discussion started by: HandleX
1 Replies
6. SCO
I have a SCO 5.07 Server and I am trying to get it on my network. I have edited the /etc/hosts file and /etc/rc2.d/s99route . I has connectivity on the NIC card but not sure if I am forgetting another file. Thanks! (2 Replies)
Discussion started by: andrewd
2 Replies
7. UNIX for Dummies Questions & Answers
I am using solaris 10, my internet works alright but each time i reboot i keep loosing my connection. I will have to use the
ifconfig iprb0 192.168.1.xx netmask 255.255.255.0 up and
Route add default 192.168.1.xxx command to gain back my internet.
I know there is a better way of addressing... (1 Reply)
Discussion started by: seyiisq
1 Replies
8. Solaris
Hi
I have installed Solaris 5.10 on Intel x86 machine (standalone).
I want to access internet through solaris. How should I configure the network? Is static IP or DHCP advisable? (5 Replies)
Discussion started by: johnl
5 Replies
9. UNIX for Advanced & Expert Users
Hi all,
I got following configuration problem
I need to configure tiny network on openbsd
I got server1 with 3 interfaces vic0 em0 em1
The interface vic0 on server1 has follwoing IP 172.16.1.1
em0
firstly I would like to configure network under em0 (I have assigned to em0 following... (1 Reply)
Discussion started by: kvok
1 Replies
LEARN ABOUT FREEBSD
atmaddr
ATMADDR(8) Maintenance Commands ATMADDR(8)
NAME
atmaddr - list and maintain local ATM addresses
SYNOPSIS
atmaddr [-n] [itf]
atmaddr -r [itf]
atmaddr -a [itf] atm_addr
atmaddr -d [itf] atm_addr
atmaddr -V
DESCRIPTION
atmaddr is used to list the local addresses configured for ATM interfaces and to manually change the list of addresses. If the interface
number itf is omitted, interface 0 is used by default. The ATM address atm_addr can be any valid ATM SVC address, e.g. an E.164 address or
an ATM Forum NSAP address.
If invoked without options, atmaddr lists the addresses that are currently configured on the specified interface.
Note that local ATM addresses are normally automatically maintained by the ILMI demon.
OPTIONS
-a append the specified address at the end of the list.
-d delete the specified address from the list.
-n numeric address output only. No address to name translation is attempted.
-r reset (clear) the local address list of the specified interface.
-V print the version number of atmaddr on standard output and exit.
AUTHOR
Werner Almesberger, EPFL ICA <Werner.Almesberger@epfl.ch>
SEE ALSO
ilmid(8)
Linux April 26, 2000 ATMADDR(8)