Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Network minimal configuration and startup
Operating Systems AIX Network minimal configuration and startup Post 302108060 by backslash on Thursday 22nd of February 2007 04:21:26 PM
Old 02-22-2007
Network minimal configuration and startup
Hi,

I have a LPAR running AIX 5.3 with multiple Etherchannels running (e.g. ent10-ent14 etc).

The person who configured up the interfaces set more that one interface through minimal config and startup under smitty->tcpip

When I try and clear out the IP address for one of the additional interfaces smit complains that the IP address is invalid because it is blank. How do I remove the additional IP addresses to leave only one primary interface?

I will configure up the addidtional IPs using smitty->tcpip-> additional configuration.

TIA
 

9 More Discussions You Might Find Interesting

1. HP-UX

HP-UX Network Configuration

Hi, I have installed a HP-UX B.11.00 U 9000/800 Server in one of the domain. And I'm also able to telnet/ping into this server from systems in the same domain. But I'm not able to telnet/ping into this server from a different domain. So, what shoud need to do to achieve this... (6 Replies)
Discussion started by: S.Vishwanath
6 Replies

2. Solaris

network configuration

hi again... i configured my network settings sometiime ago using the sys-unconfig command.the active link was rtls0. there was some problem with the network so i changed the ISP. now when im trying to reconfigure the system wit sys-unconfig, it tries to configure the network on rtls1 (and shows... (1 Reply)
Discussion started by: strider
1 Replies

3. Solaris

Specifying network configuration info

Can someone please point me in the correct direction of where I configure the network information on SunOS 5.8 server? (Searching SunSolve and Google have resulted in thousands of fixes for potential errors, but I can't find the general instructions, etc. for starting the process). Thanks! (2 Replies)
Discussion started by: FredSmith
2 Replies

4. Slackware

Network Startup Problems

I recently installed slackware 11 and have been very happy with it until I found out that some gnome related apps can cause gnome's network manager to alter the rc.init1 script by adding 3 lines to the script containing only the command, eth_up. This causes the script not to run properly and not... (1 Reply)
Discussion started by: djtrippin
1 Replies

5. UNIX for Dummies Questions & Answers

Network Configuration Commands.....

I need to know what commands I will need to use to change a host name, IP Address, and network configurations (routerings, dns, etc) and a Unix SCO machine. Also, if there is any short tutorials on using the commands, i would defiently like that information. Thanks!!! (1 Reply)
Discussion started by: HandleX
1 Replies

6. SCO

Network Configuration

I have a SCO 5.07 Server and I am trying to get it on my network. I have edited the /etc/hosts file and /etc/rc2.d/s99route . I has connectivity on the NIC card but not sure if I am forgetting another file. Thanks! (2 Replies)
Discussion started by: andrewd
2 Replies

7. UNIX for Dummies Questions & Answers

network configuration

I am using solaris 10, my internet works alright but each time i reboot i keep loosing my connection. I will have to use the ifconfig iprb0 192.168.1.xx netmask 255.255.255.0 up and Route add default 192.168.1.xxx command to gain back my internet. I know there is a better way of addressing... (1 Reply)
Discussion started by: seyiisq
1 Replies

8. Solaris

Network configuration

Hi I have installed Solaris 5.10 on Intel x86 machine (standalone). I want to access internet through solaris. How should I configure the network? Is static IP or DHCP advisable? (5 Replies)
Discussion started by: johnl
5 Replies

9. UNIX for Advanced & Expert Users

network configuration on openbsd

Hi all, I got following configuration problem I need to configure tiny network on openbsd I got server1 with 3 interfaces vic0 em0 em1 The interface vic0 on server1 has follwoing IP 172.16.1.1 em0 firstly I would like to configure network under em0 (I have assigned to em0 following... (1 Reply)
Discussion started by: kvok
1 Replies

LEARN ABOUT X11R4

systemd-networkd-wait-online.service

SYSTEMD-NETWORKD-WAIT-ONLINE.SERVICE(8) 		     systemd-networkd.service			   SYSTEMD-NETWORKD-WAIT-ONLINE.SERVICE(8)

NAME

       systemd-networkd-wait-online.service, systemd-networkd-wait-online - Wait for network to come online

SYNOPSIS

       systemd-networkd-wait-online.service

       /lib/systemd/systemd-networkd-wait-online

DESCRIPTION

       systemd-networkd-wait-online is a one-shot system service that waits for the network to be configured. By default, it will wait for all
       links it is aware of and which are managed by systemd-networkd.service(8) to be fully configured or failed, and for at least one link to
       gain a carrier.

OPTIONS

       The following options are understood:

       -i, --interface=
	   Network interface to wait for before deciding if the system is online. This is useful when a system has several interfaces which will
	   be configured, but a particular one is necessary to access some network resources. This option may be used more than once to wait for
	   multiple network interfaces. When used, all other interfaces are ignored.

       --ignore=
	   Network interfaces to be ignored when deciding if the system is online. By default, only the loopback interface is ignored. This option
	   may be used more than once to ignore multiple network interfaces.

       --timeout=
	   Fail the service if the network is not online by the time the timeout elapses. A timeout of 0 disables the timeout. Defaults to 120
	   seconds.

SEE ALSO

       systemd(1), systemd-networkd.service(8)

systemd 237												   SYSTEMD-NETWORKD-WAIT-ONLINE.SERVICE(8)
All times are GMT -4. The time now is 06:06 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy