Sponsored Content
Operating Systems Solaris Solaris 9 on x86- Can't detect network interface Post 302107669 by lowbyte on Tuesday 20th of February 2007 03:10:09 AM
Old 02-20-2007
Hey,

you need a driver for your network card.
Take a look at this link:
http://www.bolthole.com/solaris/x86-laptops.html

CU
lowbyte
 

9 More Discussions You Might Find Interesting

1. Solaris

Getting a solaris x86 box on my network.

How would i get my solaris 10 box to run on my network? (1 Reply)
Discussion started by: possuman72
1 Replies

2. Solaris

network interface problem solaris 2.5

Hi guys, Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot). I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies

3. Solaris

Solaris 10 x86 bge0 network problem

Hi, Server --Dell Poweredge 2550. OS--Solaris 10 Network switch --cisco --port setting- 1000Mbps full duplex The network LED goes off when the solaris console screen comes up but prior to that(while booting is in progess) it is green. The system is not able to come on network,ping to switch... (3 Replies)
Discussion started by: anilzoc
3 Replies

4. Solaris

Route new network interface Solaris 8

Hi there, I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far: # route add... (2 Replies)
Discussion started by: sreiniche
2 Replies

5. Solaris

What are the kernel parameter of network interface in Solaris?

Hi gurus Could anybody tell me that what are the kernal parameter of network interface in solaris Regards (3 Replies)
Discussion started by: girish.batra
3 Replies

6. Solaris

Getting Network Interface details in solaris

Hi, /sbin/ifconfig -a when i login as guest user , output like below, lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2 inet... (5 Replies)
Discussion started by: forumguest
5 Replies

7. Solaris

Configure network interface for Solaris 10

Hi, I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface. Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies

8. Solaris

Network Interface -- Solaris

Dear All, I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface . The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped. But i find that no of Input and Output... (4 Replies)
Discussion started by: jegaraman
4 Replies

9. Solaris

Network interface configuration - Solaris 11

Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue: Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies
Ns_Url(3aolserver)					   AOLserver Library Procedures 					Ns_Url(3aolserver)

__________________________________________________________________________________________________________________________________________________

NAME
Ns_AbsoluteUrl, Ns_ParseUrl, Ns_RelativeUrl, Ns_SkipUrl - URL manipulation routines SYNOPSIS
#include "ns.h" int Ns_AbsoluteUrl(Ns_DString *pds, char *url, char *baseurl) int Ns_ParseUrl(char *url, char **pprotocol, char **phost, char **pport, char **ppath, char **ptail) char * Ns_RelativeUrl(char *url, char *location) char * Ns_SkipUrl(Ns_Request *request, int n) _________________________________________________________________ DESCRIPTION
Ns_AbsoluteUrl(pds, url, baseurl) Construct an URL based on baseurl but with as many parts of the incomplete url as possible. Return NS_OK or NS_ERROR. Ns_ParseUrl(url, pprotocol, phost, pport, ppath, ptail) Parse a URL into its component parts. Pointers to the protocol, host, port, path, and "tail" (last path element) will be set by ref- erence in the passed-in pointers. The passed-in url will be modified. Ns_RelativeUrl(url, location) If the url passed in is for this server, then the initial part of the URL is stripped off. e.g., on a server whose location is http://www.foo.com, Ns_RelativeUrl of "http://www.foo.com/hello" will return "/hello". Returns a pointer to the beginning of the relative url in the passed-in url, or NULL if error. Will set errno on error. Ns_SkipUrl(request, n) Return a pointer n elements into the request's url. SEE ALSO
nsd(1), info(n) KEYWORDS
AOLserver 4.0 Ns_Url(3aolserver)
All times are GMT -4. The time now is 06:33 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy