02-16-2007
Even our linux was having the dual card and was facing the same issue. Thanks for confirming that the issue was with the Cisco switch. Please share with me if you have any document related to this.
10 More Discussions You Might Find Interesting
1. IP Networking
Hello this is my first post at this forum.
Apologize for my lack of network understanding
but Im posting to learn.
I have a problem reaching default gateway 10.18.110.1
If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping.
cat... (11 Replies)
Discussion started by: vettec3
11 Replies
2. Solaris
I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Discussion started by: cesmk
2 Replies
3. AIX
Hello,
I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies
4. Red Hat
I know the subject line is very similar to: destination host unreachable
but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there.
We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies
5. AIX
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks... (1 Reply)
Discussion started by: witt
1 Replies
6. UNIX for Dummies Questions & Answers
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies
7. AIX
I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a
startsrc -g tcpip
... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies
8. Red Hat
Hi,
Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies
9. AIX
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies
10. UNIX for Advanced & Expert Users
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
LEARN ABOUT LINUX
pam_issue
PAM_ISSUE(8) Linux-PAM Manual PAM_ISSUE(8)
NAME
pam_issue - PAM module to add issue file to user prompt
SYNOPSIS
pam_issue.so [noesc] [issue=issue-file-name]
DESCRIPTION
pam_issue is a PAM module to prepend an issue file to the username prompt. It also by default parses escape codes in the issue file similar
to some common getty's (using x format).
Recognized escapes:
d
current day
l
name of this tty
m
machine architecture (uname -m)
machine's network node hostname (uname -n)
o
domain name of this system
release number of operating system (uname -r)
current time
s
operating system name (uname -s)
u
number of users currently logged in
U
same as u except it is suffixed with "user" or "users" (eg. "1 user" or "10 users")
v
operating system version and build date (uname -v)
OPTIONS
noesc
Turns off escape code parsing.
issue=issue-file-name
The file to output if not using the default.
MODULE TYPES PROVIDED
Only the auth module type is provided.
RETURN VALUES
PAM_BUF_ERR
Memory buffer error.
PAM_IGNORE
The prompt was already changed.
PAM_SERVICE_ERR
A service module error occurred.
PAM_SUCCESS
The new prompt was set successfully.
EXAMPLES
Add the following line to /etc/pam.d/login to set the user specific issue at login:
auth optional pam_issue.so issue=/etc/issue
SEE ALSO
pam.conf(5), pam.d(5), pam(7)
AUTHOR
pam_issue was written by Ben Collins <bcollins@debian.org>.
Linux-PAM Manual 06/04/2011 PAM_ISSUE(8)