02-16-2007
Even our linux was having the dual card and was facing the same issue. Thanks for confirming that the issue was with the Cisco switch. Please share with me if you have any document related to this.
10 More Discussions You Might Find Interesting
1. IP Networking
Hello this is my first post at this forum.
Apologize for my lack of network understanding
but Im posting to learn.
I have a problem reaching default gateway 10.18.110.1
If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping.
cat... (11 Replies)
Discussion started by: vettec3
11 Replies
2. Solaris
I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Discussion started by: cesmk
2 Replies
3. AIX
Hello,
I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies
4. Red Hat
I know the subject line is very similar to: destination host unreachable
but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there.
We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies
5. AIX
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks... (1 Reply)
Discussion started by: witt
1 Replies
6. UNIX for Dummies Questions & Answers
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies
7. AIX
I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a
startsrc -g tcpip
... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies
8. Red Hat
Hi,
Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies
9. AIX
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies
10. UNIX for Advanced & Expert Users
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
LEARN ABOUT OSX
glfrontface
GLFRONTFACE(3G) GLFRONTFACE(3G)
NAME
glFrontFace - define front- and back-facing polygons
C SPECIFICATION
void glFrontFace( GLenum mode )
PARAMETERS
mode Specifies the orientation of front-facing polygons. GL_CW and GL_CCW are accepted. The initial value is GL_CCW.
DESCRIPTION
In a scene composed entirely of opaque closed surfaces, back-facing polygons are never visible. Eliminating these invisible polygons has
the obvious benefit of speeding up the rendering of the image. To enable and disable elimination of back-facing polygons, call glEnable
and glDisable with argument GL_CULL_FACE.
The projection of a polygon to window coordinates is said to have clockwise winding if an imaginary object following the path from its
first vertex, its second vertex, and so on, to its last vertex, and finally back to its first vertex, moves in a clockwise direction about
the interior of the polygon. The polygon's winding is said to be counterclockwise if the imaginary object following the same path moves in
a counterclockwise direction about the interior of the polygon. glFrontFace specifies whether polygons with clockwise winding in window
coordinates, or counterclockwise winding in window coordinates, are taken to be front-facing. Passing GL_CCW to mode selects counterclock-
wise polygons as front-facing; GL_CW selects clockwise polygons as front-facing. By default, counterclockwise polygons are taken to be
front-facing.
ERRORS
GL_INVALID_ENUM is generated if mode is not an accepted value.
GL_INVALID_OPERATION is generated if glFrontFace is executed between the execution of glBegin and the corresponding execution of glEnd.
ASSOCIATED GETS
glGet with argument GL_FRONT_FACE
SEE ALSO
glCullFace, glLightModel
GLFRONTFACE(3G)