01-30-2007
/dev/urandom
Hi, how do I use /dev/urandom to generate a single number between 1-100? I can od /dev/urandom but it gives me an endless list of random numbers, I just want 1 between 1-100. How can I get that? Thanks.
8 More Discussions You Might Find Interesting
1. Solaris
Hi, Anyone can help
My solaris 8 system has the following
/dev/null , /dev/tty and /dev/console
All permission are lrwxrwxrwx
Can this be change to a non-world write ??
any impact ?? (12 Replies)
Discussion started by: civic2005
12 Replies
2. Solaris
So, we removed a LUN from the SAN and the system is refusing to remove the references to it in the /dev folder. I've done the following:
devfsadm -Cv
powermt -q
luxadm -e offline <drive path>
luxadm probe
All those commands failed to remove the path. The drive stills shows up as <drive... (13 Replies)
Discussion started by: DustinT
13 Replies
3. AIX
Hi,
How can i check that i am using RAW devices for storage in my AIX machine...
Also after adding a LUN from storage to a aix host, when i check /dev in the host, i can see both rhdisk and hdisk with same number
eg:
dcback1(root):/dev>ls -lrt | grep disk12
crw------- 1 root ... (4 Replies)
Discussion started by: jibujacob
4 Replies
4. AIX
Hello AIXians,
I can't boot my AIX, it hangs and stops at the code error: 0518
After searching google, I knew the problem is due to problems in File Systems.
So the solution is booting from any bootable media, then run these commands in maintenance mode:
#fsck -y /dev/hd4
#fsck -y... (3 Replies)
Discussion started by: Mohannad
3 Replies
5. Shell Programming and Scripting
Objective: To recreate the partitioning setup of /dev/sda on /dev/sdc
How would I parse the below information and initialize variables
(an array?) that can be used to build sgdisk commands in a script, regardless of the number of partitions?
Something along the lines of:
sgdisk -n... (12 Replies)
Discussion started by: RogerBaran
12 Replies
6. Red Hat
Hi,
Please suggest steps to change grub from /dev/sda to /dev/sdb, (1 Reply)
Discussion started by: manoj.solaris
1 Replies
7. UNIX for Advanced & Expert Users
Hi
I'm running the following command to generate a random password in a KSH script on a RHEL Linux VM but for some reason the cmd is not being closed and it's causing problems on the host.
PASSWORD="$(cat /dev/urandom | tr -dc "a-zA-Z0-9" | fold -w 16 | head -1)Aa0!"
The code worked as... (2 Replies)
Discussion started by: user052009
2 Replies
8. HP-UX
Hi,
In our HP-UX B.11.11. I could not find dev/urandom and dev/random
Are all pseudo-devices implemented as device drivers, or in need to run /configure some package to install the package to have dev/urandom.
Please help (4 Replies)
Discussion started by: rashi
4 Replies
LEARN ABOUT DEBIAN
bup-margin
bup-margin(1) General Commands Manual bup-margin(1)
NAME
bup-margin - figure out your deduplication safety margin
SYNOPSIS
bup margin [options...]
DESCRIPTION
bup margin iterates through all objects in your bup repository, calculating the largest number of prefix bits shared between any two
entries. This number, n, identifies the longest subset of SHA-1 you could use and still encounter a collision between your object ids.
For example, one system that was tested had a collection of 11 million objects (70 GB), and bup margin returned 45. That means a 46-bit
hash would be sufficient to avoid all collisions among that set of objects; each object in that repository could be uniquely identified by
its first 46 bits.
The number of bits needed seems to increase by about 1 or 2 for every doubling of the number of objects. Since SHA-1 hashes have 160 bits,
that leaves 115 bits of margin. Of course, because SHA-1 hashes are essentially random, it's theoretically possible to use many more bits
with far fewer objects.
If you're paranoid about the possibility of SHA-1 collisions, you can monitor your repository by running bup margin occasionally to see if
you're getting dangerously close to 160 bits.
OPTIONS
--predict
Guess the offset into each index file where a particular object will appear, and report the maximum deviation of the correct answer
from the guess. This is potentially useful for tuning an interpolation search algorithm.
--ignore-midx
don't use .midx files, use only .idx files. This is only really useful when used with --predict.
EXAMPLE
$ bup margin
Reading indexes: 100.00% (1612581/1612581), done.
40
40 matching prefix bits
1.94 bits per doubling
120 bits (61.86 doublings) remaining
4.19338e+18 times larger is possible
Everyone on earth could have 625878182 data sets
like yours, all in one repository, and we would
expect 1 object collision.
$ bup margin --predict
PackIdxList: using 1 index.
Reading indexes: 100.00% (1612581/1612581), done.
915 of 1612581 (0.057%)
SEE ALSO
bup-midx(1), bup-save(1)
BUP
Part of the bup(1) suite.
AUTHORS
Avery Pennarun <apenwarr@gmail.com>.
Bup unknown- bup-margin(1)