01-13-2007
uname -S
hi ,
i have made a mistake
on the production enviourment by change tha host name .
after that i returned back the old name.
but i think this will not afeect the system until reboot the machine.
laso i tried to telnet the syetem by the host name not by the IP address and it works fine.
does this affect the system????????????????????????????????
9 More Discussions You Might Find Interesting
1. Linux
what is the difference between
uname -m and uname -i
what it actually means (2 Replies)
Discussion started by: Dileepsp
2 Replies
2. AIX
hi freinds recently i have change hostname node as using uname -s ******* but next time i saw the name using uname -n the name did t changed is that i have to reboot the system (4 Replies)
Discussion started by: senmak
4 Replies
3. Solaris
hi all,
Operating System Name : Unix Sun Solaris
Operating system release level : 5.10
Operating system version : Generic_137111-06
i know the release level that is kernel version
Generic_137111-06 what is number... (6 Replies)
Discussion started by: coxmanchester
6 Replies
4. UNIX for Dummies Questions & Answers
Hi,
Can anyone let me know the -n option in uname command in unix?
Gone through the man pages of uname, but unable to interpret.
Thanks in advance. (1 Reply)
Discussion started by: venkatesht
1 Replies
5. UNIX for Advanced & Expert Users
Using the command :
echo $eup_terminal_code | tr -s 'mil vrn qcm' 'mci pql qcm'
it works,but this translation changes depending on the system.
I'd like to define the following variables ,one for each system :
mil22h_from='mil vrn frl'
mil22h_to='mci vci fci'
... (4 Replies)
Discussion started by: Pierluigi.sala
4 Replies
6. Fedora
Hi all,
I am ssh'ed into a cluster and want to install a package. However, I don't know which type to chose (CentOS, Fedora, OpenSuSE are some of the options).
I ran called uname with various arguments but none are specific...
$ uname -n
resolute.research...
$ uname -i
x86_64
$ uname... (6 Replies)
Discussion started by: neurorad
6 Replies
7. UNIX for Dummies Questions & Answers
Can anyone please let me know the meaning of output of uname -a ?
I am totally new to unix or linux and just thinking to start learning.
When I run uname -a the output I get is -
"Linux blx28ap01 2.6.18-238.12.1.el5 #1 SMP Sat May 7 20:18:50 EDT 2011 x86_64 x86_64 x86_64 GNU/Linux"
I want to... (7 Replies)
Discussion started by: csrohit
7 Replies
8. Solaris
bssmsrv223:/ 53 ] uname -a
SunOS bssmsrv223 5.10 Generic_118833-36 sun4u sparc SUNW,Sun-Fire-V245
bssmsrv223:/ 54 ]
what does 118833-36 denotes in Generic_118833-36 (2 Replies)
Discussion started by: hiten.r.chauhan
2 Replies
9. Linux
Hi,
What is the exact output tells me when i issued UNAME and WHO ?
Regards,
Nantha.Y (2 Replies)
Discussion started by: Nandy
2 Replies
LEARN ABOUT CENTOS
telnet-probe
TELNET-PROBE(1) General Commands Manual TELNET-PROBE(1)
NAME
telnet-probe - lightweight telnet-like port probe
SYNOPSIS
$PCP_BINADM_DIR/telnet-probe [-c] [-v] host port
DESCRIPTION
telnet-probe allows the pmdashping(1) daemons to establish connections to arbitrary local and remote service-providing daemons so that
response time and service availability information can be obtained.
The required host and port number arguments have the same meaning as their telnet(1) equivalents.
The -c option causes telnet-probe to perform a connect(2) only. This skips the read(2) and write(2) exercise that would otherwise be done
after connecting (see below).
The -v option causes telnet-probe to be verbose while operating.
Once the telnet connection has been established, telnet-probe reads from stdin until end-of-file, and writes all the input data to the tel-
net connection. Next, telnet-probe will read from the telnet connection until end-of-file, discarding whatever data it receives. Then
telnet-probe exits.
To operate successfully, the input passed via telnet-probe to the remote service must be sufficient to cause the remote service to close
the connection when the last line of input has been processed, e.g. ending with ``quit'' when probing SMTP on port 25.
By default telnet-probe will not produce any output, unless there is an error in which case a diagnostic message can be displayed (in ver-
bose mode only) and the exit status will be non-zero indicating a failure.
PCP ENVIRONMENT
Environment variables with the prefix PCP_ are used to parameterize the file and directory names used by PCP. On each installation, the
file /etc/pcp.conf contains the local values for these variables. The $PCP_CONF variable may be used to specify an alternative configura-
tion file, as described in pcp.conf(5).
DIAGNOSTICS
If telnet-probe succeeds, then 0 will be returned. If the attempt to establish a connection fails or is terminated, then a non-zero exit
status is returned.
SEE ALSO
PCPintro(1), pmdashping(1), pmie(1), telnet(1), connect(2), read(2) and write(2).
Performance Co-Pilot PCP TELNET-PROBE(1)