Sponsored Content
Full Discussion: Device allocation on an LPAR
Operating Systems AIX Device allocation on an LPAR Post 302101776 by johnf on Thursday 4th of January 2007 10:06:31 AM
Old 01-04-2007
Device allocation on an LPAR

Has anyone ever encountered the following error message:

Unable to allocate the I/O slot ,,,,,,, for activation. This I/O slot is identified as a required adapter to activate this partition.

This was sent to me by one of the AIX admins working with me.
 

6 More Discussions You Might Find Interesting

1. Programming

dynamic allocation vs static allocation in c

i wrote a tiny version of tail command using a large buffer statically allocated but, in a second time, i found another version in which i use a bidimensional array dynamically allocated. here is the first version /*my tiny tail, it prints the last 5 line of a file */ #include<stdio.h>... (4 Replies)
Discussion started by: lucasclaus
4 Replies

2. AIX

LPAR freezes after switching of storage (lpar is mirrored)

Hi all, I have the following configuration 2 ds3524 storage disk systems located over 2 locations 2 P720 server located over 2 locations DS3524 are connected to san switch. Each vio server has 1 fc adapter attached to a san switch. per p720 server 2 virtual io servers. Vio 1 has 1 lun... (2 Replies)
Discussion started by: markiemark
2 Replies

3. Solaris

Block-based allocation and Extent-based allocation in Solaris

Hi guys! Could you tell me what's this figure about? (See the attached figure below.) This is a representation of block allocation filesystem and extent allocation filesystem in Solaris. Does this mean that in a block-based allocation, data are placed in individual blocks while in... (0 Replies)
Discussion started by: arah
0 Replies

4. Red Hat

Unable To Activate Ethernet Network Device in RHEL 5.5 - e100 device eth0 does not seem to be presen

Hi All, Could anyone please help to resolve the below problem. I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error. I spent 2 days for the above and go through with several suggestion found by googling. But no luck. ... (0 Replies)
Discussion started by: Tanmoy
0 Replies

5. AIX

How to differentiate between a standalone LPAR and a VIOC (which again is a lpar)?

There can be configurations in IBM Server wherein a standalone partition is created on some supported IBM Server Or A VIOS - VIOC LPARs created. Now in both cases they are lpars. But if I want to differentiate b/w a standalone LPAR vs an VIOC LPAR how can I do..? On a... (2 Replies)
Discussion started by: Manish00712
2 Replies

6. HP-UX

Failed to open tape device /dev/rmt/0mn:Device busy (errno = 16)

Hi, Unable to make tape backup, please help. /opt/ignite/bin/make_tape_recovery -a /dev/rmt/?mn -I -v -m tar -x inc_entire=vg00 * Creating local directories for configuration files and archive. ======= 04/25/16 16:28:08 IST Started /opt/ignite/bin/make_tape_recovery. (Mon... (4 Replies)
Discussion started by: anuragr
4 Replies
socal(7D)							      Devices								 socal(7D)

NAME
socal - Serial Optical Controller for Fibre Channel Arbitrated Loop (SOC+) device driver SYNOPSIS
socal@sbus-slot,0 DESCRIPTION
The Fibre Channel Host Bus Adapter is an SBus card which implements two full duplex Fibre Channel interfaces. Each Fibre Channel interface can connect to a Fibre Channel Arbitrated Loop (FC-AL). The socal device driver is a nexus driver and implements portions of the FC-2 and FC-4 layers of FC-AL. FILES
/kernel/drv/socal ELF Kernel Module ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Architecture |SPARC | +-----------------------------+-----------------------------+ SEE ALSO
sbus(4), sf(7D), ssd(7D) Writing Device Drivers ANSI X3.230-1994, Fibre Channel Physical and Signalling Interface (FC-PH) ANSI X3.272-1996, Fibre Channel Arbitrated Loop (FC-AL) Fibre Channel Private Loop SCSI Direct Attach (FC-PLDA) DIAGNOSTICS
The messages described below may appear on system console in addition to being logged. On the console, these messages are preceded by: socal%d: port %a where %d is the instance number of the socal controller and %a is the port on the host adapter. Fibre Channel Loop is ONLINE The Fibre Channel loop is now online. Fibre Channel Loop is OFFLINE The Fibre Channel loop is now offline. attach failed: device in slave-only slot. Move soc+ card to another slot. attach failed: bad soft state. Driver did not attach, devices will be inaccessible. attach failed: unable to alloc xport struct. Driver did not attach, devices will be inaccessible. attach failed: unable to map eeprom Driver was unable to map device memory; check for bad hardware. Driver did not attach to device, devices will be inaccessible. attach failed: unable to map XRAM Driver was unable to map device memory; check for bad hardware. Driver did not attach to device, devices will be inaccessible. attach failed: unable to map registers Driver was unable to map device registers; check for bad hardware. Driver did not attach to device, devices will be inaccessible. attach failed: unable to access status register Driver was unable to map device registers; check for bad hardware. Driver did not attach to device, devices will be inaccessible. attach failed: unable to install interrupt handler Driver was not able to add the interrupt routine to the kernel. Driver did not attach to device, devices will be inaccessible. attach failed: unable to access host adapter XRAM Driver was unable to access device RAM; check for bad hardware. Driver did not attach to device, devices will be inaccessible. attach failed: unable to write host adapter XRAM Driver was unable to write device RAM; check for bad hardware. Driver did not attach to device, devices will be inaccessible. attach failed: read/write mismatch in XRAM Driver was unable to verify device RAM; check for bad hardware. Driver did not attach to device, devices will be inaccessible. SunOS 5.10 9 May 1997 socal(7D)
All times are GMT -4. The time now is 02:56 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy