Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Prtdiag is Not working in Solaris 8 Ver
Operating Systems Solaris Prtdiag is Not working in Solaris 8 Ver Post 302096609 by Tornado on Thursday 16th of November 2006 03:02:54 PM
Old 11-16-2006
Oh.. I just saw the error you are getting...

Try running it as root.
If this works then check the permisions on /var/run/picld_door

Running JASS sometimes does this, the JASS finish script sets default CMASK to 027.

The permisions should be set to 444
ie:
ls -l /var/run/picld_door
Dr--r--r-- 1 root root 0 Aug 27 07:40 /var/run/picld_door

This is the fix:
Code:
chmod 444 /var/run/picld_door

Tornado
 

9 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Sun Solaris "prtdiag -v" on redhat

Does anyone know of a command or list of commands that shows the same amount of detail as prtdiag -v for redhat linux? (2 Replies)
Discussion started by: brshell
2 Replies

2. Solaris

SOLARIS/BEA WEBLOGIC ver.8.1

Hello all, I am having a little issue with BEA webloigc server Version 8.1, previously, we we confugred we where able to Grep processes for BEA and we could get the processes listed now I am only able to see the start weblogic script process. the weblogic server is up and running and performing its... (2 Replies)
Discussion started by: jvgvr6
2 Replies

3. Solaris

prtdiag and memory banks

hi, we have an e6900 and my sys admin says that the number of processors and memory were reduced to 4 and 8GB. However, a prtdiag |grep Memory returns 16GB of memory. So what is my system's memory? psrinfo returns 4 online and 4 offline CPUs. Thanks. Kumar (1 Reply)
Discussion started by: kumar27
1 Replies

4. Solaris

prtdiag - Segmentation Fault

Hi, Recently installed a Firmware patch on T5120 (solaris 10,138888-03). The patch installation was Success and system came up fine as well. My apps are running fine too. Problem is prtdiag does not work as it used to earlier. the output is very different from other t5120s I have and... (1 Reply)
Discussion started by: upengan78
1 Replies

5. Solaris

SF T2000 prtdiag problem

Hi, a couple of T2000 servers did not show the component status and the output was too short. There was a patch that needed to be installed. I also updated to the latest recommended patch cluster and OBP patch. After reboot/restart of picl, it worked ok for a couple of weeks. Then suddenly it went... (12 Replies)
Discussion started by: incredible
12 Replies

6. Solaris

Executable compiled on solaris 10 not working on solaris 9

Hi I compiled an executable on Solaris 10 which creates semaphore ( semget) but it didn't work on solaris 9 , while it is executing sucessfully on solaris 10. It is throwing the system error that Invalid arguments ( system error 22) on solaris 9. the ldd for the executable on two servers is as... (4 Replies)
Discussion started by: ash_bit2k2
4 Replies

7. Solaris

prtdiag output for Solaris on Fujitsu hardware shows vendor as Sun Microsystems

Hello, I was under the impression that the Header of the prtdiag output shows the hardware vendor information in the section between System Configuration and sun4u/sun4us. But on some Solaris machines which are running on Fujitsu hardware, the vendor is shown as Sun Microsystems in this... (8 Replies)
Discussion started by: chattygk
8 Replies

8. Solaris

prtdiag

Hi everyone, Please can you tell me what kind of memro we are talking about when we run : prtdiag -v Memory size: 98016 Megabytes Thank you (7 Replies)
Discussion started by: adilyos
7 Replies

9. Solaris

prtdiag -v troubleshooting

selected lines from the output of the "prtdiag -v" command on a T5240 SUN server running Solaris 10. Are the following known as FRU names and what do they mean? MB/CMP0/BR0/CH0/D0 MB/CMP0/BR0/CH1/D0 SYS/FANBD0/FM0/F0 SYS/FANBD0/FM0/F1 SYS/MB/CMP0/BR1/CH0/D1 ... (1 Reply)
Discussion started by: snoman1
1 Replies
All times are GMT -4. The time now is 05:50 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy