URGENT,URGENT- Need help tape drive installation Post: 302096568

Sponsored Content

Top Forums UNIX for Advanced & Expert Users URGENT,URGENT- Need help tape drive installation Post 302096568 by rshampshire on Thursday 16th of November 2006 09:44:49 AM

11-16-2006

Registered User

Quote:

Originally Posted by sriny

Hi,

I am trying to attach tape drive to sun V890 running Solaris 9 on it.
I have installed HBA(qlogic) in slot 1 of 0-8 slots and booted the system. I do not see HBAin prtdiag output. The tape drive is not attached to HBA. The tape drive I am going to attach is Sony AIT3.

1.How can I make my system see the HBA?
2.I Know this is a qlogic HBA and got it from SUN Micro systems.
3.Do I have to install any drivrers to see the system?
4.I do have similer one on another system and what should I check(config Information) to compare it.
5. Do I have to connect to make system see this?

Please Give me steps resolve this issue.

Is there any documentation on the net that gives me step by step installation/configuration of tape drive on soalris 9.

Thanks.

Been a while since I did this but I think the first step you need to do is to do a boot -s comand so the system knows to detect and configure the new hardware.

rshampshire

View Public Profile for rshampshire

Find all posts by rshampshire

7 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Tape Drive on Unix 7.1.1

I am trying to install a tape drive on this system (Unix 7.1.1) where will I start? 1. Do I need to load the driver on the on board scsi? How? 2. Is there a driver for the tape drive itself? Things done: 1. Terminated the device on the controller board.

2. UNIX for Dummies Questions & Answers

tape drive

Hi, I need to restore my tape backup, when I type "tape status" it gives; status : ready beginning-of-tape write-protected soft errors : 0 hard errors : 0 underruns : 3 but...

3. Solaris

Installation procedure of tape drive in OS ver 5.6

Hi, I'm executing the command devfsadm to check the tape drive as I did to 5.9 version but it gives me this message "devfsadm: not found" Is it different command to check the tape drive in 5.6 version? Thansk in advance.

4. AIX

Tape Drive

I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How...

5. Solaris

Help with tape drive

Hey folks, Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes. I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V. As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly. ...

6. HP-UX

TAPE drive

I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help? Thanks in advance

7. Shell Programming and Scripting

URGENT Reading a file and assessing the syntax shell script URGENT

I am trying to write a shell script which takes an input file as an arguement in the terminal e.g. bash shellscriptname.sh input.txt. I would like for the file to be read line by line each time checking if the .txt file contains certain words or letters(validating the syntax). If the line being...

LEARN ABOUT REDHAT

tapeinfo

TAPEINFO(1)						      General Commands Manual						       TAPEINFO(1)

NAME

       tapeinfo - report SCSI tape device info

SYNOPSIS

       tapeinfo -f <scsi-generic-device>

DESCRIPTION

       The  tapeinfo  command  reads  various information from SCSI tape drives that is not generally available via most vendors' tape drivers. It
       issues raw commands directly to the tape drive, using either the  operating  system's  SCSI  generic  device  (	e.g.  /dev/sg0	on  Linux,
       /dev/pass0 on FreeBSD) or the raw SCSI I/O ioctl on a tape device on some operating systems.

       One  good  time	to  use 'tapeinfo' is immediately after a tape i/o operation has failed. On tape drives that support HP's 'tapealert' API,
       'tapeinfo' will report a more exact description of what went wrong.

       Do be aware that 'tapeinfo' is not a substitute for your operating system's own 'mt' or similar tape driver control program. It is intended
       to supplement, not replace, programs like 'mt' that access your operating system's tape driver in order to report or set information.

OPTIONS

       The first argument, given following -f , is the SCSI generic device corresponding to your tape drive.  Consult your operating system's doc-
       umentation for more information (for example, under Linux these are generally start at /dev/sg0 under FreeBSD these start at /dev/pass0).

       Under FreeBSD, 'camcontrol devlist' will tell you what SCSI devices you have, along with which 'pass' device controls  them.  Under  Linux,
       "cat /proc/scsi/scsi" will tell you what SCSI devices you have.

BUGS AND LIMITATIONS

       This program has only been tested on Linux with a limited number of tape drives (HP DDS4, Seagate AIT).

AVAILABILITY

       tapeinfo  is  currently being maintained by Eric Lee Green <eric@badtux.org> formerly of Enhanced Software Technologies Inc. The 'mtx' home
       page is http://mtx.sourceforge.net and the actual code is currently available there and via CVS from http://sourceforge.net/projects/mtx/ .

SEE ALSO

       mt(1),mtx(1),scsitape(1)

								    TAPEINFO1.0 						       TAPEINFO(1)