Network interface Qfe, ce, bge ... Post: 302094592

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

2. UNIX for Advanced & Expert Users

Hi expert, Need some help on network interface issue.. I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0...

3. Solaris

qfe errors and network cards

Hi All, Hope you are all doing good. In MY unix box i have 2 network cards. I want to know what if one network card fails. Does the second one will automatically take all the traffic or how it is supposed to work. Also in my logs i am seeing below errors . Can you throw some light of this qfe...

4. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

5. Solaris

Network Interface -- Solaris

Dear All, I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface . The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped. But i find that no of Input and Output...

6. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

7. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

8. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

LEARN ABOUT REDHAT

hme

HME(4)							   BSD Kernel Interfaces Manual 						    HME(4)

NAME

     hme -- Sun Microelectronics STP2002-STQ Ethernet interfaces device driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device miibus
	   device hme

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   if_hme_load="YES"

DESCRIPTION

     The hme driver supports Sun Microelectronics STP2002-STQ ``Happy Meal Ethernet'' Fast Ethernet interfaces.

     All controllers supported by the hme driver have TCP checksum offload capability for both receive and transmit, support for the reception and
     transmission of extended frames for vlan(4) and a 128-bit multicast hash filter.

HARDWARE

     The hme driver supports the on-board Ethernet interfaces of many Sun UltraSPARC workstation and server models.

     Cards supported by the hme driver include:

     o	 Sun PCI SunSwift Adapter (``SUNW,hme'')
     o	 Sun SBus SunSwift Adapter (``hme'' and ``SUNW,hme'')
     o	 Sun PCI Sun100BaseT Adapter 2.0 (``SUNW,hme'')
     o	 Sun SBus Sun100BaseT 2.0 (``SUNW,hme'')
     o	 Sun PCI Quad FastEthernet Controller (``SUNW,qfe'')
     o	 Sun SBus Quad FastEthernet Controller (``SUNW,qfe'')

NOTES

     On sparc64 the hme driver respects the local-mac-address? system configuration variable which can be set in the Open Firmware boot monitor
     using the setenv command or by eeprom(8).	If set to ``false'' (the default), the hme driver will use the system's default MAC address for
     all of its devices.  If set to ``true'', the unique MAC address of each interface is used if present rather than the system's default MAC
     address.

     Supported interfaces having their own MAC address include on-board versions on boards equipped with more than one Ethernet interface and all
     add-on cards except the single-port SBus versions.

SEE ALSO

     altq(4), intro(4), miibus(4), netintro(4), vlan(4), eeprom(8), ifconfig(8)

     Sun Microelectronics, STP2002QFP Fast Ethernet, Parallel Port, SCSI (FEPS) User's Guide, April 1996,
     http://mediacast.sun.com/users/Barton808/media/STP2002QFP-FEPs_UG.pdf.

HISTORY

     The hme driver first appeared in NetBSD 1.5.  The first FreeBSD version to include it was FreeBSD 5.0.

AUTHORS

     The hme driver was written by Paul Kranenburg <pk@NetBSD.org>.

BSD
								   June 14, 2009							       BSD

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Discussion started by: witt

2. UNIX for Advanced & Expert Users

network interface problem

Discussion started by: sc2005