10-27-2006
It's not my LAN that can't see something. It's the LANs connected to me that can't see the BSD machine at the private address. I'm connected to these other LANs via older Cisco routers talking over T1s. Our ISP's Cisco guy said that the problem was probably the default gateway for the BSD machine at the private address. In rc.conf, sure enough, I don't have a default gateway for the machine's "inside-the-firewall" NIC. I only have a default gateway for the "outside-the-firewall" NIC. How do I set two default gateways, one for each address class I'm using?
10 More Discussions You Might Find Interesting
1. AIX
Hi friends,
I installed oracle 10g (10.2.0.2) RAC on 2 IBM p5 570 servers running AIX 5.3ML04 and HACMP5.2 (used Raw devices, not used GPFS). Each server has 4 x 1Gbps ethernet cards (NICs), en0 and en1 for boot address, en2 and en3 for oracle interconnect.
Now i want to merge 2 NICs (en2 and... (1 Reply)
Discussion started by: bong02
1 Replies
2. Solaris
Hi, is there a way in Solaris 8 to determine how many total NIC's say a Sun Sparc box has installed - plumbed or unplumbed - and find out its capable network speeds and MAC address?
I know ifconfig -a but that only shows the plumbed and used interfaces.
thx
cc (2 Replies)
Discussion started by: bigapple100
2 Replies
3. Linux
I'm looking for a way in RHL 5.1 to use two NICs on one host with two physical IP addresses and map them under one virtual IP address, i.e. NIC 1 10.10.10.1 NIC2 10.10.10.2 VIP 192.168.10.1
Basically I want either one of the NICs to ARP for the VIP. No load balancing required just HA. (2 Replies)
Discussion started by: wschmied
2 Replies
4. IP Networking
I had the pleasure of having a gig nic given to me this week, which also appears on the hardware list of FreeBSD.
What I would LIKE to do is:
1). Set my 10/100 nick as the dedicated outside/internet connection with a lan ip of 192.168.1.100
2). Set the gig nick as the dedicated... (2 Replies)
Discussion started by: droolin
2 Replies
5. Programming
Hello there,
My mulithreaded application (which is too large to represent the source code here) is crashing after installing FreeBSD 7.1-RELEASE/amd64.
It worked properly on others machines (Dual Cores with 4GB of RAM - FreeBSD 6.2-RELEASE/i386).
The current machine has 2x Core 2 Duo... (1 Reply)
Discussion started by: Seenquev
1 Replies
6. UNIX for Dummies Questions & Answers
Help, I have a Ubuntu headless server that has 5 NICs in it. The eth0-4 interfaces keep moving from NIC to NIC on boot up. I am told that there is a file that I can edit that will allow me to stabilize this but I need some help in determining the exact file and format for that file. All help will... (0 Replies)
Discussion started by: poundjd
0 Replies
7. Red Hat
I don't undestand how to combine 4 nics in order to use DM Multipath. Do I have to install each nic with its IP address? If yes, do I need a group IP address? This concept is not clear for me.
The connection beetwen the server (DELL Poweredge T710) and the SAN through iscsi works well, I used... (1 Reply)
Discussion started by: gnupinux
1 Replies
8. Hardware
Hi,
I have to get into BIOS and disable onbaord NICS for an IBM server, can someone please help me out.
I tried hitting F1 when reboot to get into BIOS, but it seems like a setup screen and I dont see any option to disable NICS?
Thanks
Sam (2 Replies)
Discussion started by: sam4919
2 Replies
9. IP Networking
Hi all,
Host - Ubuntu 12.04 desktop 64bit
Virtualizer - Oracle VirtualBox
2 NICs
Where can I find relevant document to set up 2 NICs, one for inward bound and another for outward bound, separate channel, both connected to the same router
Would following document be appropriate for my... (1 Reply)
Discussion started by: satimis
1 Replies
10. UNIX for Dummies Questions & Answers
Hello All,
I have Linux box with two interface cards.
Every card has it's own IP Address and Gateway, IP addresses are from different subnets.
eth0 192.168.1.10/24 GW 192.168.1.1
eth1 192.168.2.10/24 GW 192.168.2.1
Third PC is located in 192.168.13.0/24 network and is trying to access... (2 Replies)
Discussion started by: AndreiM
2 Replies
LEARN ABOUT CENTOS
firewall-config
FIREWALL-CONFIG(1) firewall-config FIREWALL-CONFIG(1)
NAME
firewall-config - firewalld GUI configuration tool
SYNOPSIS
firewall-config [OPTIONS...]
DESCRIPTION
firewall-config is a GUI configuration tool for firewalld.
OPTIONS
firewall-config does not support any special options. The only options that can be used are the general options that Gtk uses for Gtk
application initialization. For more information on these options, please have a look at the runtime documentation for Gtk.
The following options are supported:
-h, --help
Prints a short help text and exists.
SEE ALSO
firewall-applet(1), firewalld(1), firewall-cmd(1), firewall-config(1), firewalld.conf(5), firewalld.direct(5), firewalld.icmptype(5),
firewalld.lockdown-whitelist(5), firewall-offline-cmd(1), firewalld.richlanguage(5), firewalld.service(5), firewalld.zone(5),
firewalld.zones(5)
NOTES
firewalld home page at fedorahosted.org:
http://fedorahosted.org/firewalld/
More documentation with examples:
http://fedoraproject.org/wiki/FirewallD
AUTHORS
Thomas Woerner <twoerner@redhat.com>
Developer
Jiri Popelka <jpopelka@redhat.com>
Developer
firewalld 0.3.9 FIREWALL-CONFIG(1)