Sponsored Content
Full Discussion: sata support
Top Forums UNIX for Advanced & Expert Users sata support Post 302093173 by Corona688 on Tuesday 17th of October 2006 05:58:39 PM
Old 10-17-2006
I had this same problem with Gentoo. Brand-new system with SATA hard drive, and the Gentoo livecd would not see it. It is a catch-22 -- you need to upgrade your distribution to install on the system, but the system cannot even be installed on it.

I just dug an ancient 2GB PATA drive from my junkpile and bootstrapped from that -- installed on it, updated it and poked it until it saw the SATA drive, created partitions on the SATA drive, and copied all the files over.

I don't know if it'll be that easy on Redhat Enterprise. Does it have any copyprotection that'll go bananas when you copy it?
 

6 More Discussions You Might Find Interesting

1. Solaris

SATA driver for soalris 9

can any one help me look for a driver for SATA harddisk, im installing solaris 9 to it. thanks and regards msouthofheavenk ;) (2 Replies)
Discussion started by: msouthofheavenk
2 Replies

2. UNIX for Advanced & Expert Users

Linux o.s on two sata's.

Hi, I have two sata hard-disks. Out of those, one is having RHEL5 operating system, and other is having fedora7 operating system. When I connect the disk with RHEL5 operating system to sata0 port and disk with fedora7 operating system to sata1 port. While booting it shows RHEL5 boot screen,... (3 Replies)
Discussion started by: praveen_b744
3 Replies

3. UNIX for Advanced & Expert Users

trying to setup a sata drive using a sata to scsi adaptor

trying to setup a sata drive using a sata to scsi adaptor I have a sata 1TB Deskstar that I had setup before and during shipment from a facilty to another, the disk failed. The handling was not great, lots of throwing boxes, etc. I have a new disk from Hitachi (thankyou Hitachi) anyway, I don't... (1 Reply)
Discussion started by: mndavies
1 Replies

4. SCO

SATA Hard Disk support by SCO OpenServer 5.05

Is SATA hard disk is suooprted by SCO OpenServer 5.05? If No, how to couter this problem. If yes, please provide the installation steps. (2 Replies)
Discussion started by: rakeshkumar9919
2 Replies

5. Hardware

Connect SATA Laptop HardDrive to Desktop SATA Slots

Hello everybody, I need to connect a laptop 2.5 SATA hard drive to a Desktop board (which uses 3.5' SATA hard drives). I've tried the connectors and they fit excellent in the 2.5 SATA connectors. The problem is that the laptop hard drive uses 5v and the PC's power source sends 12v. So, my... (4 Replies)
Discussion started by: Zykl0n-B
4 Replies

6. Hardware

Question on SATA 300 vs SATA 600

I have an upgrade path in mind for a new computer that will be stocked with a 2TB SATA 300 hard disk. This is a choice based on information that SATA 300 is not necessarily faster than SATA 600. The upgrade path in a year time or so would then involve the purchase of an SSD that would contain the... (4 Replies)
Discussion started by: figaro
4 Replies
hdio(7I)							  Ioctl Requests							  hdio(7I)

NAME
hdio - SMD and IPI disk control operations SYNOPSIS
#include <sys/hdio.h> DESCRIPTION
Note - The SMC and IPI drivers have been discontinued. dkio(7I) is now the preferred method for retrieving disk information. The SMD and IPI disk drivers supplied with this release support a set of ioctl(2) requests for diagnostics and bad sector information. Basic to these ioctl() requests are the definitions in <sys/hdio.h>. IOCTLS
HDKIOCGTYPE The argument is a pointer to a hdk_type structure (described below). This ioctl() gets specific information from the hard disk. HDKIOCSTYPE The argument is a pointer to a hdk_type structure (described below). This ioctl() sets specific information about the hard disk. /* * Used for drive info */ struct hdk_type { ushort_t hdkt_hsect; /* hard sector count (read only) */ ushort_t hdkt_promrev; /* prom revision (read only) */ uchar_t hdkt_drtype; /* drive type (ctlr specific) */ uchar_t hdkt_drstat; /* drive status (ctlr specific, ro) */ }; HDKIOCGBAD The argument is a pointer to a hdk_badmap structure (described below). This ioctl() is used to get the bad sector map from the disk. HDKIOCSBAD The argument is a pointer to a hdk_badmap structure (described below). This ioctl() is used to set the bad sector map on the disk. /* * Used for bad sector map */ struct hdk_badmap { caddr_t hdkb_bufaddr; /* address of user's map buffer */ }; HDKIOCGDIAG The argument is a pointer to a hdk_diag structure (described below). This ioctl() gets the most recent command that failed along with the sector and error number from the hard disk. /* * Used for disk diagnostics */ struct hdk_diag { ushort_t hdkd_errcmd; /* most recent command in error */ daddr_t hdkd_errsect; /* most recent sector in error */ uchar_t hdkd_errno; /* most recent error number */ uchar_t hdkd_severe; /* severity of most recent error */ }; SEE ALSO
ioctl(2), dkio(7I) SunOS 5.10 13 Aug 2002 hdio(7I)
All times are GMT -4. The time now is 10:17 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy