I know this is going to be an easy anwer, but I haven't been able to figure this out - even with the help of the previous posts. I want to go from this
PROD USER anon;
to this
TEST;
I have coded a few sed commands, and none of them are getting the job done. anon will not always be the... (2 Replies)
Hi Guys/Gals,
I have a log file that is updated once every few seconds and I am looking for a way to speed up one of my scripts.
Basically what I am trying to do is grep through a text file from start to finish once. Then each subsequent grep starts at the last line of the previous grep to... (4 Replies)
Hello, Would someone guide me on how to write a shell script the would search for a phone no using at the end text file using sed or awk and store it in a varaible or print it.
The text file is in this form
text or numbers in first line
text or numbers in second line
.
.
.
Firsname... (6 Replies)
Hi Folks,
Using the Vi, how can I add a numbers at the end of the line.
For eg: I have the numbers in the file as:
58.125.33
22.58.68
25.144.225
114.25.38
I need to add .0/8 at the end of all the line. So, it should be like
58.125.33.0/8
22.58.68.0/8
25.144.225.0/8
114.25.38.0/8 (6 Replies)
Example,
Trying to replace text to the end of a line.
Text file looks like this
PP= 4
PP= 412
PP= 425
I want to replace only the following line:
PP= 4
with
PP= 2
How can this be done with sed? (3 Replies)
Does anyone know how to use awk to act like grep from a particular line number to the end of file? I am using Solaris 10 and I don't have any GNU products installed.
Say I want to print all occurrences of red starting at line 3 to the end of file.
EXAMPLE FILE:
red
green
red
red... (1 Reply)
Given a file like this:
abc
def
ghi
I need to get to
somestandardtext abc1 morestandardtext
somestandardtext def2 morestandardtext
somestandardtext ghi3 morestandardtext
Notice that in addition to the standard text there is the line number added in as well. What I conceived is... (4 Replies)
my requirement is,
consider a file output
cat output
blah sdjfhjkd jsdfhjksdh
sdfs 23423 sdfsdf sdf"sdfsdf"sdfsdf"""""dsf
hellow there
this doesnt look good
et cetc etc
etcetera
i want to replace a line of line number 4 ("this doesnt look good") with some other line
... (3 Replies)
Dear Unix Experts :),
Below is a small section of a large file with the following list:
1. Starts with string " interest" as the heading
2. Followed by a list of activities
3. Ends with a blank line before starting with another different list.
E.g.
Sporting interest
football... (13 Replies)
I all
I am tryng to find a way to sort a list of number in a file by the value of last two digit.
i have a list like this
313202320388
333202171199
373202164587
393202143736
323202132208
353201918107
343201887399
363201810249
333201805043
353201791691 (7 Replies)
Discussion started by: rattoeur
7 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)