Run the following command:
This should print all files larger than 100MB in the / filesystem. Then you can see what these files are and decide to remove/truncate/compress them.
We have SunOS 5.7 m/c. Following is the situation and problem what we are facing -
- The root partition was full.
- No login was possible on server (not from console also)
- M/c was power swithced off
- After this only console login is possible. FTP is possible. No telnet is possible.
I... (3 Replies)
We have SunOS 5.7 m/c. Following is the situation and problem what we are facing -
- The root partition was full.
- No login was possible on server (not from console also)
- M/c was power swithced off
- After this only console login is possible. FTP is possible. No telnet is possible.
I... (1 Reply)
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
HI,
Currently I am working in One of the webhosting company and I found
on one of my server "/home" partition is getting full say 105% usage...
But when I actually check the partition size using "du -h", exact partition
utilization is only 60-70%.
So... (1 Reply)
My /var partition is almost utilized ... Here am not sure where to release space now
OS/model : HP-UX B.11.11 U 9000/800
# bdf /var
Filesystem kbytes used avail %used Mounted on
/dev/vg00/lvol9 6144000 6142176 1824 100% /var
<root@pb>/var # du -sk * | sort -n |... (20 Replies)
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Good day,
Anybody, know how to clean/free up the Cluster_boot partition in TRU64
Thank you in advance
Miaka (0 Replies)
Discussion started by: miaka1012
0 Replies
LEARN ABOUT MINIX
repartit
REPARTITION(8) System Manager's Manual REPARTITION(8)NAME
repartition - load a partition table
SYNOPSIS
repartition device [partition-file]
DESCRIPTION
Repartition uploads a new partition table for the partitions of device. The table is obtained from the first sector of partition-file if
given, device otherwise. Device may refer to the whole drive or a primary partition, depending on whether you want to upload a partition
or a subpartition table. The partitions will be truncated to fit within the enclosing device like the disk driver does, unless the numbers
are coming from partition-file.
EXAMPLES
repartition /dev/hd0
repartition /dev/hd4 /etc/hd4.table
Reload the partition table of drive 0 setting /dev/hd[1-4], and the subpartition table of /dev/hd4 setting /dev/hd4[a-d] using a file. The
latter may be useful if you need more than the 4 subpartitions a single Minix partition gives you.
DIAGNOSTICS
The new table is printed on standard output.
FILES
/dev/hd[0-9]
SEE ALSO hd(4), part(8).
BUGS
The disk must be in use for the changes to stick. The partition table of an idle disk will be reloaded on the first open.
AUTHOR
Kees J. Bot (kjb@cs.vu.nl)
REPARTITION(8)