08-22-2006
in a word 'minicom' it's curses based so you don't need X.
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi,
I'm facing problem in connecting a Raid A1000 to E250 and E450. ( Both machines with Solaris 2.6 OS and patched, with different
scsi-initiator-ids - 7 & 3 ).
BTW, I'm not using this setup to access raid data from both machines simultaneously. There is Veritas Cluster Server monitoring... (1 Reply)
Discussion started by: shibz
1 Replies
2. UNIX Benchmarks
==============================================================
BYTE UNIX Benchmarks (Version 3.11)
System -- SunOS xxxxx 5.8 Generic_108528-13 sun4u sparc SUNW,Ultra-250
Start Benchmark Run: Sun Jan 11 19:47:12 EST 2004
1 interactive users.
Dhrystone 2 without register variables ... (0 Replies)
Discussion started by: kduffin
0 Replies
3. Solaris
Hi,
I have cisco console cable. One end of the cable is DB9 connector and the other end is RJ45 connector. I would like to use this cable to connect to my SUN E250 system from my pc so that I can access the SUn console directly.
I would like to know whether it is possible and also on which... (5 Replies)
Discussion started by: RajaRC
5 Replies
4. Solaris
Hi,
We have an E250 which we need to access to install solaris 10 for a communigate trial.
We only have the server itself, no cables or anything and im struggling to gain access.
It has a RSC card, that i have learned, but a db25-db9 cable doesn't seem to bring anything up in telnet on... (11 Replies)
Discussion started by: e250user
11 Replies
5. Solaris
Hi,
I need some help, since I am new to cluster.
I am handling a site where I have look after two SUN E250 server.
I have been asked to configure Active-Active Clustering on these servers.
I would like to know how to configure both the servers for clustering.
Below are the things which... (5 Replies)
Discussion started by: RajaRC
5 Replies
6. Solaris
Hello,
Running a Sun Solaris 9 E250 and need advice or suggestions on what type of external hard disks are compatible and or available. It's an old machine and is due for replacement soon but in the short term need an external hard drive for backup etc as the partner/backup machine has just... (2 Replies)
Discussion started by: KenLynch
2 Replies
7. Solaris
I've got an old E250 server where a front error LED is showing. I've read through the Sun docs (Sun Enterprise 250 Server Owner's Guide - Sun Microsystems) but it's only the 'General fault' LED (About the Status and Control Panel (Sun Enterprise 250 Server Owner's Guide) - Sun Microsystems)... (2 Replies)
Discussion started by: aussieos
2 Replies
8. Solaris
Hi everybody, my name is Giulia and for me is the fist time in this forum, i hope write in the correct section for my problem.
I have a sun solaris server e250 enterprise with sun 5 versionof O.S.
Now i wont format all and install new version of solaris, but i don't know the actual corrent... (7 Replies)
Discussion started by: giulia79
7 Replies
9. Solaris
E250 server only shows banner when powered on i am not getting OK PROMPT . .In morning it was booting with solaris 7 .i am not able to do STOP-A STOP-D .its not excepting STOP-N also.
Please help (1 Reply)
Discussion started by: monu94
1 Replies
LEARN ABOUT REDHAT
curs_print
curs_print(3X) curs_print(3X)
NAME
mcprint - ship binary data to printer
SYNOPSIS
#include <curses.h>
int mcprint(char *data, int len);
DESCRIPTION
This function uses the mc5p or mc4 and mc5 capabilities, if they are present, to ship given data to a printer attached to the terminal.
Note that the mcprint code has no way to do flow control with the printer or to know how much buffering it has. Your application is
responsible for keeping the rate of writes to the printer below its continuous throughput rate (typically about half of its nominal cps
rating). Dot-matrix printers and 6-page-per-minute lasers can typically handle 80cps, so a good conservative rule of thumb is to sleep for
a second after shipping each 80-character line.
RETURN VALUE
The mcprint function returns ERR if the write operation aborted for some reason. In this case, errno will contain either an error associ-
ated with write(2) or one of the following:
ENODEV
Capabilities for printer redirection don't exist.
ENOMEM
Couldn't allocate sufficient memory to buffer the printer write.
When mcprint succeeds, it returns the number of characters actually sent to the printer.
PORTABILITY
The mcprint call was designed for ncurses(3X), and is not found in SVr4 curses, 4.4BSD curses, or any other previous version of curses.
BUGS
Padding in the mc5p, mc4 and mc5 capabilities will not be interpreted.
SEE ALSO
curses(3X)
curs_print(3X)