08-22-2006
Dear Sona,
The error you are getting is probably because you are using "" on place of ''.
You can try this also.....it's little ugly but I think it might solve your purpose.....
sed '/[a-zA-Z0-9]* [0-9]*\.[0-9]* [0-9]*\.[0-9]*/ a\
COMMENT
' pattern.dat > test.dat
regards
Apoorva kumar
10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
I have a problem in searching a specific pattern in c files.
My requirement:
I have to find all the division operator in all cfiles.
The problem is, the multi line comments and single line comments will also have forward slash in it.
Even after avoiding these comments also, if both... (6 Replies)
Discussion started by: murthybptl
6 Replies
2. Shell Programming and Scripting
Hello,
So I sorted my file as I was supposed to:
sort -n -r -k 2 -k 1 file1 | uniq > file2
and when I wrote
> cat file2
in the command line, I got what I was expecting, but in the script itself
...
sort -n -r -k 2 -k 1 averages | uniq > temp
cat file2
It wrote a whole... (21 Replies)
Discussion started by: shira
21 Replies
3. Shell Programming and Scripting
Hi,
Please take a look at the below eg. I would like to search for abc() pattern first and then search for (xyz) in the next line. If I can find the pattern, then I should delete the 3 lines.
I can only find the pattern and delete but I am unable to find two patterns and delete. Any... (8 Replies)
Discussion started by: sreedevi
8 Replies
4. Shell Programming and Scripting
Hi All,
Please can someone assist in the script I have made that searches a pattern in a file and delete the whole line containing the pattern.
#!bin/sh
# The pattern that user want to add to the files
echo "Enter the pattern of the redirect"
read value
# check if the user has... (1 Reply)
Discussion started by: Shazin
1 Replies
5. Shell Programming and Scripting
hi All,
i want to add the single digit front of the line in the report file and string compare with pattern file.
patter file: pattern1.txt
pattern num
like 4
love 3
john 2
report file: report.txt
i like very much
but john is good boy
i will love u
so after execute... (9 Replies)
Discussion started by: krbala1985
9 Replies
6. Shell Programming and Scripting
The following text is in testFile.txt:
one 5
two 10
three 15
four 20
five 25
six 10
seven 35
eight 10
nine 45
ten 50
I'd like to use sed to print the first occurance of search pattern /10/ in a given range. This command is to be run against large log files, so to optimize efficiency,... (9 Replies)
Discussion started by: uschaafm
9 Replies
7. Shell Programming and Scripting
Hi there,
Looking forward to your advice for the below:
I have a file which contains 2 paragraphs related to a particular pattern. I have to search for those paragraphs from a log file and then print a particular line from those paragraphs.
Sample:
I have one file with the fixed... (3 Replies)
Discussion started by: danish0909
3 Replies
8. Shell Programming and Scripting
Hi All,
i have an output of command vmstat as below :
$ vmstat
System configuration: lcpu=4 mem=5376MB ent=1.00
kthr memory page faults cpu
----- ----------- ------------------------ ------------ -----------------------
r b avm fre re pi... (10 Replies)
Discussion started by: omkar.jadhav
10 Replies
9. Shell Programming and Scripting
Hi Everyone,
I have an unusual requirement. Here is where i am stuck for sometime now...
I have this text file.. lets say .. output.sql...
it has lot of entries... here below is part of the entry...
.. . . . . . . . . . . . . . . . .... (3 Replies)
Discussion started by: vivek d r
3 Replies
10. Shell Programming and Scripting
Not able to paste my content. Please see the attachment :-( (2 Replies)
Discussion started by: vivek d r
2 Replies
LEARN ABOUT V7
load_datafile
load_datafile(3alleg4) Allegro manual load_datafile(3alleg4)
NAME
load_datafile - Loads a datafile into memory. Allegro game programming library.
SYNOPSIS
#include <allegro.h>
DATAFILE *load_datafile(const char *filename);
DESCRIPTION
Loads a datafile into memory in one go. If the datafile has been encrypted, you must first call packfile_password() to set the appropriate
key. If the datafile contains truecolor graphics, you must set the video mode or call set_color_conversion() before loading it. Example:
/* Load the resources for our game. */
DATAFILE *dat = load_datafile("game.dat");
if (!dat)
abort_on_error("Couldn't load sound resources!");
/* Use resources. */
...
/* Destroy them when we don't need them any more. */
unload_datafile(dat);
RETURN VALUE
Returns a pointer to the DATAFILE, or NULL on error. Remember to free this DATAFILE later to avoid memory leaks.
SEE ALSO
load_datafile_callback(3alleg4), unload_datafile(3alleg4), load_datafile_object(3alleg4), set_color_conversion(3alleg4),
fixup_datafile(3alleg4), packfile_password(3alleg4), find_datafile_object(3alleg4), register_datafile_object(3alleg4), excustom(3alleg4),
exdata(3alleg4), exexedat(3alleg4), exgui(3alleg4), exsprite(3alleg4), exunicod(3alleg4)
Allegro version 4.4.2 load_datafile(3alleg4)