Sponsored Content
Full Discussion: Unix Telnet session
Top Forums UNIX for Dummies Questions & Answers Unix Telnet session Post 302085443 by apoorvasharma80 on Thursday 17th of August 2006 10:04:22 AM
Old 08-17-2006
I am not sure about the machine name but you can always check the IP using 'w' command!!

regards
Apoorva kumar
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

printing over tcp/ip via telnet session

I am new to unix. Currently using solaris 6.8 (i think). I need to telnet into a remote server, and print out a report to a printer near me, that DOES NOT have a printcap set-up for the printer on the remote server. I was hoping to do this via tcp/ip since the printer does have a static ip... (1 Reply)
Discussion started by: gishfarm
1 Replies

2. UNIX for Dummies Questions & Answers

telnet session timeout

hi, we can set something such that if the user has been idle for a while, it will auto disconnect. where to do so? thanks (6 Replies)
Discussion started by: yls177
6 Replies

3. Shell Programming and Scripting

Telnet session does not expire

Dear friends.. Our project has a module that runs on handheld devices. Through the handheld we telnet to solaris where the application actually runs. I noticed that after starting a session through the handheld, if i go out of range or if i remove and replace the battery in the handheld, the... (1 Reply)
Discussion started by: deepsteptom
1 Replies

4. Shell Programming and Scripting

Telnet Session

{ sleep 2 echo "$user" sleep 2 echo "$password" sleep 2 echo " ls" sleep 10 echo "exit" }| telnet $server I have a machine x and i have executed the above script on machine 'x'. i entered the... (6 Replies)
Discussion started by: pathanjalireddy
6 Replies

5. UNIX for Dummies Questions & Answers

check for successfull telnet session

In either case using ksh or tcl, how can I check that I have a successfule telnet session and am being prompted with a tacacs login prompt ? :confused: DOIT () { sleep 2 echo "<tacacs name >" sleep 1 echo "<password>" echo "en" sleep 1 echo "<enable password>" echo "term length 512"... (0 Replies)
Discussion started by: sumguy
0 Replies

6. Shell Programming and Scripting

sqlplus session being able to see unix variables session within a script

Hi there. How do I make the DB connection see the parameter variables passed to the unix script ? The code snippet below isn't working properly. sqlplus << EOF user1@db1/pass1 BEGIN PACKAGE1.perform_updates($1,$2,$3); END; EOF Thanks in advance, Abrahao. (2 Replies)
Discussion started by: 435 Gavea
2 Replies

7. UNIX for Dummies Questions & Answers

Telnet Session to AIX

Hello, I have AIX 5.3 at home connected to netgear router. Port Forwarding has been enabled on the router. Problem is that if I want to telnet, I have to try 2 or 3 times before I can get a logon prompt. It times out for first or second time (Connection to session <IP_Address> failed: Connection... (1 Reply)
Discussion started by: bluebee
1 Replies

8. UNIX for Dummies Questions & Answers

Disconnecting a telnet session

How can I disconnect an existing telnet session? The host is a serial port server with multiple ports. The users login using the host's name and a port, i.e. telnet host01 1235. Thanks. (14 Replies)
Discussion started by: cooldude
14 Replies

9. HP-UX

ssh session getting hung (smilar to hpux telnet session is getting hung after about 15 minutes)

Our network administrators implemented some sort of check to kill idle sessions and now burden is on us to run some sort of keep alive. Client based keep alive doesn't do a very good job. I have same issue with ssh. Does solution 2 provided above apply for ssh sessions also? (1 Reply)
Discussion started by: yoda9691
1 Replies
E2UNDO(8)                                                     System Manager's Manual                                                    E2UNDO(8)

NAME
e2undo - Replay an undo log for an ext2/ext3/ext4 filesystem SYNOPSIS
e2undo [ -f ] [ -h ] [ -n ] [ -o offset ] [ -v ] [ -z undo_file ] undo_log device DESCRIPTION
e2undo will replay the undo log undo_log for an ext2/ext3/ext4 filesystem found on device. This can be used to undo a failed operation by an e2fsprogs program. OPTIONS
-f Normally, e2undo will check the filesystem superblock to make sure the undo log matches with the filesystem on the device. If they do not match, e2undo will refuse to apply the undo log as a safety mechanism. The -f option disables this safety mechanism. -h Display a usage message. -n Dry-run; do not actually write blocks back to the filesystem. -o offset Specify the filesystem's offset (in bytes) from the beginning of the device or file. -v Report which block we're currently replaying. -z undo_file Before overwriting a file system block, write the old contents of the block to an undo file. This undo file can be used with e2undo(8) to restore the old contents of the file system should something go wrong. If the empty string is passed as the undo_file argument, the undo file will be written to a file named e2undo-device.e2undo in the directory specified via the E2FSPROGS_UNDO_DIR environment variable. WARNING: The undo file cannot be used to recover from a power or system crash. AUTHOR
e2undo was written by Aneesh Kumar K.V. (aneesh.kumar@linux.vnet.ibm.com) AVAILABILITY
e2undo is part of the e2fsprogs package and is available from http://e2fsprogs.sourceforge.net. SEE ALSO
mke2fs(8), tune2fs(8) E2fsprogs version 1.44.1 March 2018 E2UNDO(8)
All times are GMT -4. The time now is 04:12 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy