07-25-2006
Hi jeelans,
I think this problem caused by the swap is full. In this case the server allows only root to be accessible.To fix the problem you may reboot the server or
clear out the data in /tmp directory.
Let me know if it's still persistent.
Thanks,
Jackie.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Changed from a broken Switch to a working HUB everyting else in my network is ok after the change but not my RS/6000! It refuses to get connected, get time out on Pings both ways - strange?
Could it be some problem with ARP?:confused: (2 Replies)
Discussion started by: jolun
2 Replies
2. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
3. AIX
I have AIX 5.3 OS. After issuing the print command, the printer state immediately goes down. I have checked the /etc/qconfig flle, resatrted the qdaemon but again same problem is occuring. I am using HP 5100 connected to jetdirect.
what is the problem and it's solution? (4 Replies)
Discussion started by: prashantchavan
4 Replies
4. IP Networking
Folks;
I have 2 SUSE servers (192.168.157.100 & 192.168.157.101) both are similar and has the same gateway 192.168.157.1
I can connect to the second one from my PC just fine (192.168.157.101).
The problem is i couldn't connect to the first one using SSH even after i disabled the firewall. when i... (3 Replies)
Discussion started by: Katkota
3 Replies
5. Solaris
Hi everybody,
I have a very strange problem ; if somebody could help me it would be very kind. I'll try to explain my problem.
I have 2 unix machines absolutely identical running solaris 9.
For network reasons I need to change the IP address of the 2 machines.
I proceed exactly the same on the... (11 Replies)
Discussion started by: aribault
11 Replies
6. AIX
Dear ALL.
I installed AIX OS on customer sites.
but Only one site is too slow when I connected telnet, ftp..
Ping is too fast. but telnet and FTP is not connected..
of course i check the configuration file on aix but it's normal.
Do any Idea??
thanks in advance.
- Jun - (3 Replies)
Discussion started by: Jeon Jun Seok
3 Replies
7. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
8. AIX
Hi everbody;
I have 2 p520 machines and created a vio server for each one (vio01 - vio02). I created 3 AIX 5.3 lpars on vio02 and 3 AIX 6.1 lpars on vio01. The problem is when 2 lpars are activated, i can ping gateway from both lpars and vio; but when i activate 3rd lpar, network downs and none of... (2 Replies)
Discussion started by: lordofdarkness
2 Replies
9. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
10. Android
Good day, everybody! I have a mobile phone (LG Optimus L5) with Android 4.0.3 and a tablet (PocketBook SurfPad 2) with Android 4.1.1 and I have problem with wireless network on these devices. Laptops don't have such problem. My wireless network organisation is a modem connected with an access point... (11 Replies)
Discussion started by: qzxcvbnm
11 Replies
LEARN ABOUT SUNOS
asadmin-list-authdbs
asadmin-list-authdbs(1AS) User Commands asadmin-list-authdbs(1AS)
NAME
list-authdbs - gets the authorized database
SYNOPSIS
list-authdbs --user admin_user[--password admin_password][--host localhost] [--port 4848][--passwordfile filename][--secure|-s][--instance
instance_name] --virtualserver virtualserver_ID authdb_ID
Gets the access control lists associated with the named server instance.
OPTIONS
--user administrative user associated for the instance.
--password administrative password corresponding to the administrative user.
--host host name of the machine hosting the administrative instance.
--port administrative port number associated with the administrative host.
--passwordfile file containing passwords appropriate for the command (e.g., administrative instance).
--secure if true, uses SSL/TLS to communicate with the administrative instance.
--virtualserver virtual server ID. It can also be referred to as the variable $id in an obj.conf file. A virtual server ID cannot
begin with a number.
OPERANDS
instance_name name of the instance.
Example 1: Using list-authdbs
asadmin> lsit-authdbs --user admin --password adminadmin --host fuyako --port 7070 --virtualserver server1 server1
default
sampleAuth
Where: default and sampleAuth are the authdb IDs in virtual server server1 and instance server1 listed.
asadmin% list-authdbs --instance server1
EXIT STATUS
0 command executed successfully
1 error in executing the command
asadmin-create-authdb(1AS), asadmin-delete-authdb(1AS)
J2EE 1.4 SDK March 2004 asadmin-list-authdbs(1AS)