Seems to be a problem of routing. Perhaps you had the default route through en0.
Notice both interfaces are in the same network.
Post the output of
after and before pulling the cable, and let's see.
Regards.
Hello
am asking for your help on printer issues.
i wanted to change the current printer we have now, basically bec we needed a more durable one. so recently i have a product demo, but its driver is not present in UNIX. i will be using the same network printer name but different model.... (0 Replies)
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Hi All,
This is regarding problem with two servers...
EX:- server1(HP) is not able to connect with proxy server server2(SUN BOX)
But we can able to login.... server1 is not able to pickup any data from the proxy server...
checked in the sunbox...
# ping bdhp5050
server1 is alive
... (1 Reply)
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
I have AIX 5.3 OS. After issuing the print command, the printer state immediately goes down. I have checked the /etc/qconfig flle, resatrted the qdaemon but again same problem is occuring. I am using HP 5100 connected to jetdirect.
what is the problem and it's solution? (4 Replies)
Folks;
I have 2 SUSE servers (192.168.157.100 & 192.168.157.101) both are similar and has the same gateway 192.168.157.1
I can connect to the second one from my PC just fine (192.168.157.101).
The problem is i couldn't connect to the first one using SSH even after i disabled the firewall. when i... (3 Replies)
hi all, i manage a network of 120 windows xp systems and my gateway run on centos 4.6 i actually config the linux gateway my self and i config iptable rules as well.until now, all has been fine but the problem now is that amunable to browse the network using my network places from some of the... (1 Reply)
Dear ALL.
I installed AIX OS on customer sites.
but Only one site is too slow when I connected telnet, ftp..
Ping is too fast. but telnet and FTP is not connected..
of course i check the configuration file on aix but it's normal.
Do any Idea??
thanks in advance.
- Jun - (3 Replies)
Hi everbody;
I have 2 p520 machines and created a vio server for each one (vio01 - vio02). I created 3 AIX 5.3 lpars on vio02 and 3 AIX 6.1 lpars on vio01. The problem is when 2 lpars are activated, i can ping gateway from both lpars and vio; but when i activate 3rd lpar, network downs and none of... (2 Replies)
This is a LPAR that i created earlier.
I want to set an IP address to en0 but it failed.
Command: failed stdout: yes stderr: no
Before command completion, additional instructions may appear below.
en0
devdbm01
inet0 changed
Method error (/usr/lib/methods/chgif):
... (8 Replies)
Discussion started by: wingcross
8 Replies
LEARN ABOUT CENTOS
en
EN(4) BSD Kernel Interfaces Manual EN(4)NAME
en -- device driver for Midway-based ATM interfaces
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device en
device atm
device utopia
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_en_load="YES"
DESCRIPTION
The en device driver supports Midway-based ATM interfaces including the Efficient Networks, Inc. ENI-155 and Adaptec ANA-59x0. Midway is an
AAL5 SAR (Segmentation and Reassembly) chip.
For configuring the card for IP see natmip(4).
The following sysctls are recognized by the driver additionally to those handled by utopia(4):
hw.atm.enX.istats
Contains an array of uint32_t with internal driver statistics.
hw.atm.enX.debug
This is a bit map of debugging options. This variable is only available when the driver is compiled with debugging support.
The driver supports the media options sdh, noscramb and unassigned (see utopia(4)).
DIAGNOSTICS
en0 <Efficient Networks ENI-155p> rev 0 int a irq 5 on pci0:16
en0: ATM midway v0, board IDs 6.0, Utopia (pipelined), 512KB on-board RAM
en0: maximum DMA burst length = 64 bytes
en0: 7 32KB receive buffers, 8 32KB transmit buffers allocated
CAVEATS
The driver extensively uses DMA on PCI. The first generation PCI chipsets do not work or exhibit poor performance.
SEE ALSO natm(4), natmip(4), utopia(4), ifconfig(8), route(8)AUTHORS
Chuck Cranor of Washington University implemented en driver in 1996 for NetBSD.
BSD July 16, 2005 BSD