Please help to configure Sun Blade 150 workstation Post: 302080767

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Memory upgrade Sun Blade 150

I would like to upgrade the memory in my Sun Blade 150 workstation. In reading through Sun's Blade 150 DIMM Installation Guide, it indicates that the memory must be "certified by Sun for the Sun Blade 150 system." Does anyone know if any SDRAM, PC133 � CL=2 � Unbuffered � ECC � 133MHz � 3.3V ...

2. UNIX for Dummies Questions & Answers

How to configure a network workstation to a standalone?

Hi, I have a networked ultra 5 workstation(using NIS) that I would like to be able to : 1. Reconfigure to standalone workstation, 2. and be able to switch back to a network workstation when the needs required. Please advise. Ryan

3. Solaris

Sun Blade 150 - I can't hook up extra drives

I'm not familiar with this particular machine and it's baffling me. For those that are familar with the workstation, allow me to paint a picture. If you were looking down on the machine (open) you would see the main board and then a riser board. On the left side of the riser board are jacks...

4. Solaris

Jumpstart Solaris 8 on Sun Blade 150 Hangs

We had to replace a hard drive in one of our Sun Blade 150s, but now it hangs during the Jumpstart. It will show 1 or 2 Timeout for ARP/RARP messages and then start the spinning numbers. It always stops at 2ae00 and just hangs there. We have 1 combined jumpstart server and it is also our NIS+...

5. Solaris

Solaris: Blade 150 - XWINDOWS Problem

Hi, I have a Solaris 8.0 BLADE 150 machine. I have an onboard graphics alongwith an addon XVR500 graphics card. Now, when I use the motherboard graphics, I am not able to login to the XWINDOWS terminal, instead it stays on the console. But, if I insert the monitor cable to the XVR500 port,...

6. Solaris

Sun Blade 150 not a Sun?

I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05. I have just noticed /bin/sun now returns false, rather than true. See below. $ uname -a SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100 $ /bin/sparc &&...

7. Solaris

Sun Blade 150 wont boot off cdrom

Hello, Ive just aquired a blade 150 off ebay.Im new to suns and are having a problem getting it to boot off the cdrom.Openboot continuously tries to do a network boot and I cant enter any commands.Im using an average pc keyboard and it definetly works.Thanks for any help.:wall:

8. Solaris

Sun Blade 150 will not boot off harddrive after install of solaris 10

Hello, I cant get my blade box to boot off the harddrive after installing solaris 10.I can get to a root prompt after issuing "boot cdrom -s".I tried booting off disk0 and disk1,but I get "the file just loaded does not seem to be executable".Thanks for any help.:wall:

9. Solaris

Cannot install or run Solaris 8 on Sun Blade 150

Hi everybody, I'm having big troubles in installing Solaris 8 on a Sun Blade 150. Here are some system specs: Sun Blade 150 (UltraSPARC-IIe 550MHz) RAM: 256MB OBP 4.10.6 2003/06/06 12:30 POST 2.0.1 2001/08/23 17:13 When I try to boot from Solaris 8 CD with boot cdrom or...

10. Solaris

Execution problems with sun blade 150

hello i have a forte gamma camera Philips device . and its a medical device. this medical device is came with sun blade 150 pc and pegasys is printed on the sun blade pc .the problem is when i switched the power on , the sun blade runs and a white screen appear with the information about the...

LEARN ABOUT NETBSD

aac

AAC(4)							   BSD Kernel Interfaces Manual 						    AAC(4)

NAME

     aac -- Adaptec AdvancedRAID Controller driver

SYNOPSIS

     aac* at pci? dev ? function ?
     ld* at aac? unit ?

DESCRIPTION

     The aac driver provides support for the Adaptec AAC family of SCSI and SATA RAID controllers.  These controllers support RAID 0, 1, 5, 10,
     and volume sets.  They have four channels in the add-in version or 1-2 channels in the motherboard integrated version, and are most often
     found rebadged by Dell, Hewlett-Packard or IBM.  Supported controllers include:

     o	 Adaptec AAC-364
     o	 Adaptec SCSI RAID 2120S
     o	 Adaptec SCSI RAID 2200S
     o	 Adaptec SATA RAID 2410SA
     o	 Adaptec SATA RAID 3405
     o	 Adaptec SCSI RAID 5400S
     o	 Dell PERC 2/Si
     o	 Dell PERC 2/QC
     o	 Dell PERC 3/Di
     o	 Dell PERC 3/Si
     o	 Dell PERC 320/DC
     o	 Dell CERC SATA RAID 1.5/6ch
     o	 HP NetRAID 4M
     o	 HP ML110 G2 (Adaptec SATA RAID 2610SA)
     o	 IBM ServeRAID 8k

     Access to RAID containers is available via the ld device driver.  Individual drives cannot be accessed unless they are part of a container or
     volume set, and non-fixed disks cannot be accessed.  Containers can be configured by using the on-board BIOS utility of the card.

DIAGNOSTICS

     The adapter can send status and alert messages asynchronously to the driver.  These messages are printed on the system console.

SEE ALSO

     intro(4), ld(4)

HISTORY

     The aac driver first appeared in NetBSD 1.6, and was based on the FreeBSD driver of the same name.

BUGS

     This driver is not compatible with controllers that have version 1.x firmware.  The firmware version is the same as the kernel version
     printed in the BIOS POST and driver attach messages.

BSD
								 February 19, 2011							       BSD