Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Error in creating logical partition
Top Forums UNIX for Dummies Questions & Answers Error in creating logical partition Post 302080715 by RTM on Thursday 20th of July 2006 09:05:45 AM
Old 07-20-2006
I'm not a expert in SCO - but in dealing with creating logical/physical drives and mapping them incorrectly, you normally have to back out of what you did and start over. If you have been running with this condition and now have data you can't lose, then I suggest you 'backup' anything you can and start over.

See the system admin guide for more assistance - note this one is for 5.0.7.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

understanding logical partition, physical partition

hi, 1) is logical partition the same as physical partition except that one is physical and the other is logical? 2) then it must a one to one ratio? (3 Replies)
Discussion started by: yls177
3 Replies

2. IP Networking

ifconfig: difference between creating logical or alias network interface

Hi guys, I have set up multiple virtual FTP servers on a server through one physical NIC. I believe there are to ways; setting logical or alias ip's. I would like to know what is the difference between setting up a logical ip or setting up an alias ip to a physical network interface? Some links to... (5 Replies)
Discussion started by: zaff
5 Replies

3. AIX

Increase a logical partition

hello I have a volume group of 737 Go (EMC) To add 250 Go, i split the 250 Go to 2*125 No problem to add in the volum group, but when i want to increase the size of the logical volume, i have the message : 0516-787 extendlv: Maximum allocation for logical volume simdatabaselv is... (3 Replies)
Discussion started by: pascalbout
3 Replies

4. AIX

How to match a logical partition to a file

I would like to know how to identify which file a logical partition relates too. Operating System = AIX oslevel -s = 5300-04-CSP I've identified a logical volume that continually runs at 100% tm_acct from iostat. I've run lvmstat -l and identified the logical partition 590, being the... (1 Reply)
Discussion started by: garry
1 Replies

5. AIX

AIX procedure for creating a logical volume from CLI

Hi, What is the typical AIX procedure for creating a logical volume from CLI. I have mostly worked on HPUX so far and on which the typica steps are: 1: pvcreate -f /dev/rdsk/<mydisk> 2: mkdir /dev/<myvg> 3: mknod /dev/<myvg>/group C 64 <0x030000> 4: vgcreate /dev/<myvg>... (2 Replies)
Discussion started by: amit4g
2 Replies

6. Solaris

Using / Formating a Logical Partition as I cant see it

Hi All, I have managed to install and configure a Solaris x86 server, the problem I have now is that whilst setting it up, I left a 30GB logical partition for the Oracle database server that I will later have on the system, the problem now is that I have not formatted the drive during... (18 Replies)
Discussion started by: platforminc
18 Replies

7. Solaris

Creating a partition....???

I have created a pool named earthpool using zpool command. Later I created a file system named earth using zfs command. I changed the mountpoint of earth (file system) using zfs set mountpoint=/earth earthpool/earth. Where /earth is a directory created in root using mkdir. Now, I have a... (8 Replies)
Discussion started by: bharu_sri
8 Replies

8. UNIX for Advanced & Expert Users

[Solved] Creating unformatted partition

I needed to create a un-formatted partition of X MB on a disk dont want it from GUI but from command line not sure what should be specified for fdisk (4 Replies)
Discussion started by: dinjo_jo
4 Replies

9. HP-UX

Creating a logical volume file

Hi to all, I am brand new to HP-UX but am quite familiar with Linux systems (Red Hat, Ubuntu etc..) I've just taken over a new HP-UX box and trying to work out how to create a logical volume. As well as creating the volume, which I am sure is very easy I need to create a special character... (6 Replies)
Discussion started by: jamie2teach
6 Replies

10. Solaris

Partition overlaps another partition while creating new parition in solaris

hi all while formatting hard disk i am getting following error. Partition 1 ends at 266338338 It must be between 34 and 143374704. label error: EFI Labels do not support overlapping partitions Partition 8 overlaps partition 1. Warning: error writing EFI. Label failed. I have formatted the... (2 Replies)
Discussion started by: nikhil kasar
2 Replies

LEARN ABOUT NETBSD

ch

CH(4)							   BSD Kernel Interfaces Manual 						     CH(4)

NAME

     ch -- SCSI media changer driver

SYNOPSIS

     ch* at scsibus? target ? lun ?

DESCRIPTION

     The ch driver is essentially an ioctl(2) interface to a robot on a SCSI bus - a device that will change media (e.g. tapes, CD-ROMs, etc) in
     and out of drives for that media.	The chio(1) utility program uses this interface to manipulate such robots.

FILES

     /dev/chu	    SCSI bus media changer unit u
     /usr/include/sys/chio.h

DIAGNOSTICS

     ch%d: waiting %d seconds for changer to settle...	Some changers require a long time to settle out, to do tape inventory, for instance.

     ch%d: offline  The changer is not responding.

     ch%d: warning, READ ELEMENT STATUS avail != count
     ch%d: could not sense element address page
     ch%d: could not sense capabilities page

SEE ALSO

     chio(1), ioctl(2), cd(4), intro(4), scsi(4), st(4)

AUTHORS

     Jason R. Thorpe

BSD
								   June 10, 1998							       BSD
All times are GMT -4. The time now is 10:30 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy