E250 - need to access it Post: 302080668

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Need help to access/mount so to access folder/files on a Remote System using Linux OS

Hi I need to access files from a specific folder of a Linux system from an another Linux System Remotely. I know how to, Export a folder on One SCO System & can access the same by using Import via., NFS in the Sco Unix SVR4 System using the scoadmin utility. Also, I know to use mount -t ...

2. UNIX for Advanced & Expert Users

Raid A1000 with E450 and E250.

Hi, I'm facing problem in connecting a Raid A1000 to E250 and E450. ( Both machines with Solaris 2.6 OS and patched, with different scsi-initiator-ids - 7 & 3 ). BTW, I'm not using this setup to access raid data from both machines simultaneously. There is Veritas Cluster Server monitoring...

3. UNIX Benchmarks

Sun E250 / 512MB Ram

============================================================== BYTE UNIX Benchmarks (Version 3.11) System -- SunOS xxxxx 5.8 Generic_108528-13 sun4u sparc SUNW,Ultra-250 Start Benchmark Run: Sun Jan 11 19:47:12 EST 2004 1 interactive users. Dhrystone 2 without register variables ...

4. Solaris

SUN E250 Console connectivity

Hi, I have cisco console cable. One end of the cable is DB9 connector and the other end is RJ45 connector. I would like to use this cable to connect to my SUN E250 system from my pc so that I can access the SUn console directly. I would like to know whether it is possible and also on which...

5. Gentoo

Uses for a Sun e250?

We are retiring a Sun e250 at work, and I wondered if I could put it to any good use. Will I have any problems loading Linux as opposed to Solaris? Should I use any particular flavor of Linux that might be more Sun friendly? Assuming I manage to load Linux on this server, then what? Will it be...

6. Solaris

SUN E250 Cluster

Hi, I need some help, since I am new to cluster. I am handling a site where I have look after two SUN E250 server. I have been asked to configure Active-Active Clustering on these servers. I would like to know how to configure both the servers for clustering. Below are the things which...

7. Solaris

Sun Solaris 9 E250 -- Suggestions For External Hard Drives

Hello, Running a Sun Solaris 9 E250 and need advice or suggestions on what type of external hard disks are compatible and or available. It's an old machine and is due for replacement soon but in the short term need an external hard drive for backup etc as the partner/backup machine has just...

8. Solaris

Error LED showing on E250

I've got an old E250 server where a front error LED is showing. I've read through the Sun docs (Sun Enterprise 250 Server Owner's Guide - Sun Microsystems) but it's only the 'General fault' LED (About the Status and Control Panel (Sun Enterprise 250 Server Owner's Guide) - Sun Microsystems)...

9. Solaris

Sun Solaris Enterprise E250 x64 Help

Hi everybody, my name is Giulia and for me is the fist time in this forum, i hope write in the correct section for my problem. I have a sun solaris server e250 enterprise with sun 5 versionof O.S. Now i wont format all and install new version of solaris, but i don't know the actual corrent...

10. Solaris

E250 server not getting ok prompt

E250 server only shows banner when powered on i am not getting OK PROMPT . .In morning it was booting with solaris 7 .i am not able to do STOP-A STOP-D .its not excepting STOP-N also. Please help

LEARN ABOUT V7

liebert

LIEBERT(8)							    NUT Manual								LIEBERT(8)

NAME

       liebert - Driver for Liebert contact-closure UPS equipment

NOTE

       This man page only documents the hardware-specific features of the liebert driver. For information about the core driver, see nutupsdrv(8).

SUPPORTED HARDWARE

       This driver supports some Liebert UPS equipment with a contact-closure interface. This includes the UPStation GXT2 with their
       contact-closure cable. The smart mode ("Multilink") cable is not supported by this driver.

EXTRA ARGUMENTS

       This driver does not support any extra settings in the ups.conf(5).

BUGS

       This driver does not yet support shutdowns by raising DTR. Be aware that shutdowns are not possible with the stock contact-closure cable.
       You may have to build another cable with DTR connected through to the UPS for it to work.

       There is no way for this driver to detect the hardware or cable. It will start up successfully even if no UPS is present. This is a
       fundamental limitation of any contact-closure driver.

SEE ALSO

   The core driver:
       nutupsdrv(8)

   Internet resources:
       The NUT (Network UPS Tools) home page: http://www.networkupstools.org/

Network UPS Tools						    05/21/2012								LIEBERT(8)