|
|
Sponsored Content
Operating Systems
Solaris
E250 - need to access it
Post 302080665 by reborg on Thursday 20th of July 2006 06:04:26 AM
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi
I need to access files from a specific folder of a Linux system from an another Linux System Remotely.
I know how to, Export a folder on One SCO System & can access the same by using Import via., NFS in the Sco Unix SVR4 System using the scoadmin utility.
Also, I know to use mount -t ... (2 Replies)
Discussion started by: S.Vishwanath
2 Replies
2. UNIX for Advanced & Expert Users
Hi,
I'm facing problem in connecting a Raid A1000 to E250 and E450. ( Both machines with Solaris 2.6 OS and patched, with different
scsi-initiator-ids - 7 & 3 ).
BTW, I'm not using this setup to access raid data from both machines simultaneously. There is Veritas Cluster Server monitoring... (1 Reply)
Discussion started by: shibz
1 Replies
3. UNIX Benchmarks
==============================================================
BYTE UNIX Benchmarks (Version 3.11)
System -- SunOS xxxxx 5.8 Generic_108528-13 sun4u sparc SUNW,Ultra-250
Start Benchmark Run: Sun Jan 11 19:47:12 EST 2004
1 interactive users.
Dhrystone 2 without register variables ... (0 Replies)
Discussion started by: kduffin
0 Replies
4. Solaris
Hi,
I have cisco console cable. One end of the cable is DB9 connector and the other end is RJ45 connector. I would like to use this cable to connect to my SUN E250 system from my pc so that I can access the SUn console directly.
I would like to know whether it is possible and also on which... (5 Replies)
Discussion started by: RajaRC
5 Replies
5. Gentoo
We are retiring a Sun e250 at work, and I wondered if I could put it to any good use. Will I have any problems loading Linux as opposed to Solaris? Should I use any particular flavor of Linux that might be more Sun friendly? Assuming I manage to load Linux on this server, then what? Will it be... (9 Replies)
Discussion started by: kccrusher
9 Replies
6. Solaris
Hi,
I need some help, since I am new to cluster.
I am handling a site where I have look after two SUN E250 server.
I have been asked to configure Active-Active Clustering on these servers.
I would like to know how to configure both the servers for clustering.
Below are the things which... (5 Replies)
Discussion started by: RajaRC
5 Replies
7. Solaris
Hello,
Running a Sun Solaris 9 E250 and need advice or suggestions on what type of external hard disks are compatible and or available. It's an old machine and is due for replacement soon but in the short term need an external hard drive for backup etc as the partner/backup machine has just... (2 Replies)
Discussion started by: KenLynch
2 Replies
8. Solaris
I've got an old E250 server where a front error LED is showing. I've read through the Sun docs (Sun Enterprise 250 Server Owner's Guide - Sun Microsystems) but it's only the 'General fault' LED (About the Status and Control Panel (Sun Enterprise 250 Server Owner's Guide) - Sun Microsystems)... (2 Replies)
Discussion started by: aussieos
2 Replies
9. Solaris
Hi everybody, my name is Giulia and for me is the fist time in this forum, i hope write in the correct section for my problem.
I have a sun solaris server e250 enterprise with sun 5 versionof O.S.
Now i wont format all and install new version of solaris, but i don't know the actual corrent... (7 Replies)
Discussion started by: giulia79
7 Replies
10. Solaris
E250 server only shows banner when powered on i am not getting OK PROMPT . .In morning it was booting with solaris 7 .i am not able to do STOP-A STOP-D .its not excepting STOP-N also.
Please help (1 Reply)
Discussion started by: monu94
1 Replies
LEARN ABOUT ULTRIX
mdc
mdc(4) Kernel Interfaces Manual mdc(4) Name mdc - DS5100 serial line driver Syntax device mdc0 at ibus? vector mdcintr device mdc1 at ibus? vector mdcintr device mdc2 at ibus? vector mdcintr Description A DS5100 base system (mdc0) provides four asynchronous ports. An optional asynchronous card (mdc1 and mdc2 ) can be added to supply eight additional ports. The mdc ports are used as follows: Port Usage Connector 0 Console port 6-pin MMJ on CPU board 1 Local terminal 6-pin MMJ on CPU board 2 Full modem control port 25-pin D-Sub on CPU board 3 Local terminal 6-pin MMJ on CPU board An optional asynchronous board provides an additional eight lines: 4 Local terminal 6-pin MMJ 5 Local terminal 6-pin MMJ 6 Full modem control port 25-pin D-Sub 7 Local terminal 6-pin MMJ 8 Local terminal 6-pin MMJ 9 Local terminal 6-pin MMJ 10 Local terminal 6-pin MMJ 11 Local terminal 6-pin MMJ The console baud rate is set to 9600 baud by default. You can change this by setting the baud environment variable from console prompt. Each communication port from the serial line controller behaves as described in the reference page and can be set to run at any of 16 speeds. For the encoding, see You can establish the state of port 2 (port 6) by specifying either modem or nomodem as part of the file entry. Restrictions The speed default is to 9600 baud on the console port. The console device must be set for 8-bit character length with one stop bit and no parity. The driver enforces these restrictions; that is, changing speeds with the command may not always work on console ports. Files Console terminal Full modem control or local terminal See Also console(4), devio(4), tty(4), ttys(5), MAKEDEV(8) RISC mdc(4)