07-11-2006
Maybe try insmod=ide-generic on the boot line, I remember someone having a similar problem here with a version of SuSE 9.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I believe i have most of samba configured right but i get this error each time time try to run it. I was given suggestion that i touch the file, i did, but i still cannot rid myself of this error.
Any suggestions (2 Replies)
Discussion started by: macdonto
2 Replies
2. Linux Benchmarks
Notes:
System Configuration: Dell Computer Corporation PowerEdge 4600 (4 X Intel(R) XEON(TM) CPU 2.00GHz
1988.782 MHz) hyperthreaded
System clock frequency: 99.0827 MHz
Memory size (approximate): 2559 Megabytes
========================= CPUs ========================
CPU # CPU... (0 Replies)
Discussion started by: tnorth
0 Replies
3. Linux Benchmarks
CPU/Speed: Dual PIII 533
Ram: 256Mb PC133
Motherboard: Unknown, Intel Chipset
Cache: 256k on board
Controller: PARC Raid 2/Si, AIC-7880U
Disk: 30Gb RAID 5
Load: 1 user. Clean boot, init 5 but X-Windows not loaded.
Kernel: See Benchmarks.
pgms: gcc 3.2.3
... (2 Replies)
Discussion started by: Garp
2 Replies
4. Solaris
hi, i am trying to install solaris 10 (on 4 cd's downloaded from the sun website) on my dell poweredge 2800 server. 2 xeon processors, 2GB of RAM and 2 NICS, 73 GB SCSI (maxtor ultra320, 3.5 series), i can give more details on request...
the installation crashes when trying to detect the NICS... (0 Replies)
Discussion started by: xinugeek
0 Replies
5. Filesystems, Disks and Memory
Does anybody no how to get around the fact that the Red Hat installation does not see the SCSI hard drives. It lets you manually pick the proper device, but still fails saying no drive detected (or something to that effect). I was going to install windows 2003 Server and use VMware...but again,... (1 Reply)
Discussion started by: Fatflea
1 Replies
6. Programming
Hi,
I have a C++ program to access /dev/mem and retrieve details like Vendor, Manufacturer details of the motherboard. This works fine on all the machines except for on Dell Poweredge 2850,1950... machines.
I receive a 'EFAULT' when I try to access /dev/mem on these servers.
I suspect some... (1 Reply)
Discussion started by: ragisreekanth
1 Replies
7. SCO
I was asked to get a Dell PowerEdge 2600 server, out of warranty, running SCO 3.2v5.06 to perform a full backup. I spent hours researching and preparing a strategy only to fail on-site.
The only device names in /dev for a tape drive were
/dev/xStp0
/dev/xcdt0
/dev/xct0
... (6 Replies)
Discussion started by: ezlarry
6 Replies
8. Programming
Dear Team
I am using DB2 v10 z/os database . Need expert guidance to figure out best way to track table activities ( Ex Delete, Insert,Update )
Scenario
We have a table which is critical and many developer/testing team access on daily basis . We had instance where some deleted... (1 Reply)
Discussion started by: Perlbaby
1 Replies
9. UNIX for Beginners Questions & Answers
My server has /var/log/messages with 'init: initLogger main process (608798) terminated with status 1' errors. I researched about the error and also followed the steps from stackexchange :
157059/error-init-ttys0-dev-ttys0-main-process-1612-terminated-with-status-1]linux - ERROR: init: ttyS0... (0 Replies)
Discussion started by: Paras Pandey
0 Replies
LEARN ABOUT LINUX
startpar
STARTPAR(8) System Manager's Manual STARTPAR(8)
NAME
startpar - start runlevel scripts in parallel
SYNOPSIS
startpar [-p par] [-i iorate] [-t timeout] [-T global_timeout] [-a arg] prg1 prg2 ...
startpar [-p par] [-i iorate] [-t timeout] [-T global_timeout] -M [ boot|start|stop]
DESCRIPTION
startpar is used to run multiple run-level scripts in parallel. The degree of parallelism on one CPU can be set with the -p option, the
default is full parallelism. An argument to all of the scripts can be provided with the -a option. Processes block by pending I/O will
weighting by the factor 800. To change this factor the option -i can be used to specify an other value.
The output of each script is buffered and written when the script exits, so output lines of different scripts won't mix. You can modify
this behaviour by setting a timeout.
The timeout set with the -t option is used as buffer timeout. If the output buffer of a script is not empty and the last output was timeout
seconds ago, startpar will flush the buffer.
The -T option timeout works more globally. If no output is printed for more than global_timeout seconds, startpar will flush the buffer of
the script with the oldest output. Afterwards it will only print output of this script until it is finished.
The -M option switches startpar into a make(1) like behaviour. This option takes three different arguments: boot, start, and stop for
reading .depend.boot or .depend.start or .depend.stop respectively in the directory /etc/init.d/. By scanning the boot and runlevel direc-
tories in /etc/init.d/ it then executes the appropriate scripts in parallel.
FILES
/etc/init.d/.depend.boot
/etc/init.d/.depend.start
/etc/init.d/.depend.stop
SEE ALSO
init.d(7), insserv(8), startproc(8).
COPYRIGHT
2003,2004 SuSE Linux AG, Nuernberg, Germany.
2007 SuSE LINUX Products GmbH, Nuernberg, Germany.
AUTHOR
Michael Schroeder <mls@suse.de>
Takashi Iwai <tiwai@suse.de>
Werner Fink <werner@suse.de>
Jun 2003 STARTPAR(8)