Sponsored Content
Full Discussion: devices in solaris 10
Operating Systems Solaris devices in solaris 10 Post 302078839 by bondoq on Wednesday 5th of July 2006 03:06:56 AM
Old 07-05-2006
devices in solaris 10

i want to use the devfsadm command and understand its function
 

9 More Discussions You Might Find Interesting

1. Solaris

Disk devices in solaris 10 x86

I'm trying to mirror 2 eide disks on a solaris 10 x86 system. Im trying to use the prtvtoc | fmthard command to mirror the vtoc. How do they represent the entire disk like in solaris 9 (c0t0d0s2 = entire device) 0. c0d0 <DEFAULT cyl 26497 alt 2 hd 16 sec 63> ... (1 Reply)
Discussion started by: BG_JrAdmin
1 Replies

2. UNIX for Dummies Questions & Answers

Solaris print devices

I've been looking in my /dev directory for my available devices to set up a printer and was expecting to see some lp or lpr devices using Solaris 8, but I do not see them so I'm a little confused? Any help would be greatly appreciated. (2 Replies)
Discussion started by: jroglass
2 Replies

3. Solaris

Solaris I386 ifconfig devices ??

I want to configure my Network card. On solaris 9 i386. How to know the good Network device. I use prtconf to display the device list. I'm searching the device name. Like ifconfig device_name plumb thanks you (2 Replies)
Discussion started by: simquest
2 Replies

4. Solaris

solaris way if interpreting devices?

Hi all, I wanted to know the solaris way of interpreting devices? I mean i understand all those c0t0....stuff but when i start mounting devices , most of the times i get either a I/O error or it says that the directory does not exist. eg: I have a external usb hub to which i have connected... (1 Reply)
Discussion started by: wrapster
1 Replies

5. Solaris

solaris I/O devices info

Hi, can anyone help in finding the hardware related details of I/O devices of remote solaris machine .Thanks in advance. (7 Replies)
Discussion started by: pratheepv
7 Replies

6. Solaris

Solaris zone devices

Hello all, I'm having issue with trying to add device resource to my zone from the global zone. I did the following zoncfg -x larryase add device set match="/dev/tty*" end I get device already set, but in me zone I don't see the device. Is there a "reboot -- r" command for zones? or... (0 Replies)
Discussion started by: larryase
0 Replies

7. Solaris

Looking for Solaris 10 10/09 Drivers for these Devices

Could anyone tell me where I can obtain Solaris 10 10/09 drivers for these divices listed below. I have looked in the OpenSolaris forums but I have not had any luck. Device Vendor Device Name Network Atheros AR928X Wireless Network Adapter (PCI-Express) Storage Intel 82801 SATA... (4 Replies)
Discussion started by: Tenyhwa
4 Replies

8. Solaris

USCSICMD ioctl calls for Fibre Channel(FC) devices on Solaris 10?

Hi , I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Discussion started by: naveen448
0 Replies

9. Solaris

Solaris 11 and OpenSolaris both hang at Configuring Devices

Hi, Any help would be appreciated, when I attempt to install either OpenSolaris or Solaris 11 the install hangs right after the copyright where normally it would be "configuring devices" . If it is SOL 11 it just hangs if it is OpenSolaris it starts spitting out the following: WARNING: hubdi:... (0 Replies)
Discussion started by: jk121960
0 Replies
install-solaris(1M)													       install-solaris(1M)

NAME
install-solaris - install the Solaris operating system SYNOPSIS
install-solaris install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation, install-solaris invokes either a text-based installer or a graphical installer. The following minimum requirements for physical memory dictate which features are available during installation: For SPARC machines: 128 MB Minimum physical memory for all installation types 128 MB Minimum physical memory required for windowing system 384 MB Minimum physical memory required for graphical-based installation For x86 machines: 256 MB Minimum physical memory for all installation types 256 MB Minimum physical memory required for windowing system 512 MB Minimum physical memory required for graphical-based installation In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea- tures available. install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more details. install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the installation media. Refer to the for disk space requirements. Refer to the for more information on the various menus and selections. See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcdrom (Solaris instal- | | |lation media) | +-----------------------------+-----------------------------+ |Interface Stability |Evolving | +-----------------------------+-----------------------------+ pkginfo(1), install(1M), pkgadd(1M), attributes(5) It is advisable to exit install-solaris by means of the exit options in the install-solaris menus. 23 Sep 2005 install-solaris(1M)
All times are GMT -4. The time now is 07:10 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy