06-06-2006
help with jumpstart
Hello all,
I configured a jumpstart server ( the server is in the same subnet as the client) and gave boot net - install in the client.
The client boots up shows the banner and then displays error:
cant read disk label
cant open disk label package
and then goes to OK prompt.
What could be the problem? Thanks in advance for any suggestions.
PraArj
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have been asked to research Jumpstart and don't know where to begin! Any ideas would be much appreciated! Thanks! :-) (1 Reply)
Discussion started by: avana100
1 Replies
2. UNIX for Dummies Questions & Answers
Hi,
Which sites have general information on JumpStart for Solaris 8?
I would like to know more about boot server, installation server, and configuration server.... and all other good things about JumpStart....Thanks..:p
Doo... (2 Replies)
Discussion started by: dookeobih
2 Replies
3. UNIX for Advanced & Expert Users
HI.
i was wondering if you can jumpstart using the solaris intel platform? please help thanks (3 Replies)
Discussion started by: souldier
3 Replies
4. UNIX for Advanced & Expert Users
Hi,
where can i find documention on how to create a jumpstart system?
dori (2 Replies)
Discussion started by: dorilevy
2 Replies
5. Solaris
Hi Peeps,
Created a jumpstart server for an unattened install and it works, but got 2 bugs in the config which I would like to work out:
when you boot net install
It still asks you to select a language and locale, after you do this it kicks of an unattended install.
So my question is,... (5 Replies)
Discussion started by: callmebob
5 Replies
6. Solaris
Hi all ,
I am trying to jumpstart ( webstart) solaris 9 on E2900 ( client) using the DVD of a V440 server ( jumstart server). I did the setup for the V440 as follows :
cleaning up preexisting install client "XXXXXXX"
removing XXXXXXXfrom bootparams
removing /etc/bootparams, since it is... (14 Replies)
Discussion started by: ppass
14 Replies
7. Solaris
1.I wish to perform a Jumpstart installation, the client being Ultra 5 Sparc
and jumpstart Server being ultra 20 AMD system.
2.I think i have done all the procedures right, like putting the mac address of Sparc 1 to /etc/ethers, creating sysidcfg file, and profile file:
3.When I issued the boot... (7 Replies)
Discussion started by: saagar
7 Replies
8. Solaris
Hi Gurus,
Can you please suggest me any good guides for a Beginner to learn Solaris Jumpstart.
Thank You,
Rama Krishna. (2 Replies)
Discussion started by: rama krishna
2 Replies
9. Solaris
I have a laptop and need to build an Oracle Linux kickstart server and a Solaris Jumpstart server that can build sparc and x86 systems.
Is the best way to create a dual boot from grub for Oracle Linux and Solaris x86?
Can the Oracle Kickstart be used as a Jumpstart to build both Solaris 10... (2 Replies)
Discussion started by: Gian
2 Replies
10. Solaris
Hi Guys,
I am little bit confused about jumpstart on solaris 10.
Do you need the mac address for each system you intend to jumpstart? If you need the mac address, how will you get it? Say your server is in another location and you want to jumpstart it, how will you do it?
Clarification on... (1 Reply)
Discussion started by: cjashu
1 Replies
LEARN ABOUT OSX
nns_common
nameserv::common(n) Name service facility nameserv::common(n)
__________________________________________________________________________________________________________________________________________________
NAME
nameserv::common - Name service facility, shared definitions
SYNOPSIS
package require Tcl 8
package require nameserv::common ?0.1?
::nameserv::common::port
_________________________________________________________________
DESCRIPTION
Please read Name service facility, introduction first.
This package is internal and of no interest to users. It provides the commands of the name service facility which are shared by the client
and server implemented by the packages nameserv::server and nameserv (the client).
This service is built in top of and for the package comm. It has nothing to do with the Internet's Domain Name System. If the reader is
looking for a package dealing with that please see Tcllib's packages dns and resolv.
API
The package exports a single command, as specified below:
::nameserv::common::port
The result returned by the command is the id of the default TCP/IP port a nameservice server will listen on, and a name service
client will try to connect to.
BUGS, IDEAS, FEEDBACK
This document, and the package it describes, will undoubtedly contain bugs and other problems. Please report such in the category nameserv
of the Tcllib SF Trackers [http://sourceforge.net/tracker/?group_id=12883]. Please also report any ideas for enhancements you may have for
either package and/or documentation.
SEE ALSO
nameserv::client(n), nameserv::server(n)
KEYWORDS
client, name service, server
CATEGORY
Networking
COPYRIGHT
Copyright (c) 2007-2008 Andreas Kupries <andreas_kupries@users.sourceforge.net>
nns 0.1 nameserv::common(n)