05-12-2006
What Perderabo said, although I disagree with calling a sigle disk a stripe.
In a two disk 1+0 each disk would be a single disk concatenation, rather than a single disk stripe, it is a little pedantic to make the destinction with only two disks, but the difference only becomes apparrent when adding extra disk to the setup.
9 More Discussions You Might Find Interesting
1. Solaris
hi all...sudhansu here............ i need some help..........
what is RAID 0+1 and RAID 1+0.............what is the difference between them................
suppose i have 80 gb disk space,then which RAID level i follow n why......... i need redundancy n maximum storage..........please help (3 Replies)
Discussion started by: sudhansu
3 Replies
2. Solaris
Somebody can help me ! how can i do mirror in sun ver 8
without third party software !!! (3 Replies)
Discussion started by: goldfelda
3 Replies
3. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
4. Solaris
Dear ALl,
I have a RAID 5 volume which is as below
d120 r 60GB c1t2d0s5 c1t3d0s5 c1t4d0s5 c1t5d0s5
d7 r 99GB c1t2d0s0 c1t3d0s0 c1t4d0s0 c1t5d0s0
d110 r 99GB c1t2d0s4 c1t3d0s4 c1t4d0s4 c1t5d0s4
d8 r 99GB c1t2d0s1 c1t3d0s1... (2 Replies)
Discussion started by: jegaraman
2 Replies
5. Solaris
Hello All,
I have read enough of texts on Raid 01 and Raid 10 on solaris :wall: . But no-where found a way to create them using SVM. Some one pls tell me how to do or Post some link if that helps.
TIA
Curious
solarister (1 Reply)
Discussion started by: Solarister
1 Replies
6. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
7. UNIX for Dummies Questions & Answers
Hi Gurus,
Can any one explain me the difference between hardware RAID and s/w RAID.
Thanks in Advance. (1 Reply)
Discussion started by: rama krishna
1 Replies
8. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
9. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
ASR(4) BSD Kernel Interfaces Manual ASR(4)
NAME
asr -- driver for Adaptec I2O based SCSI/ATA host bus adapters
SYNOPSIS
device asr
DESCRIPTION
The Adaptec asr driver provides access to disks and disk arrays controlled by I2O based host bus adapters and SmartRAID SCSI RAID adapters
through the standard SCSI disk da(4) interface.
The supported adapters provide 64 bit PCI, Compact PCI, Zero Channel PCI, and up to four channels of Ultra2, Ultra 160, or Ultra320 SCSI, or
two channels of 1GB Fibre. All support RAID-0, RAID-1, RAID-10, RAID-5 and RAID-50 arrays. All SCSI target types are supported. For the
ATA based controllers, one IDE drive per channel is supported. Hot-swapping of IDE drives is not supported at this time.
All host bus adapters must be configured before they can be used with any operating system. Please contact Adaptec directly to obtain the
latest information on configuration utilities for the adapters. Currently there are both a Motif based GUI configuration utility and a CLI
based configuration utility available from the Adaptec Web site. The cards and arrays can also be configured via the BIOS based configura-
tion tool (SMOR).
HARDWARE
The adapters currently supported by the asr driver include the following:
o Adaptec Zero-Channel SCSI RAID 2000S, 2005S, 2010S, 2015S
o Adaptec SCSI RAID 2100S, 2110S
o Adaptec ATA-100 RAID 2400A
o Adaptec SCSI RAID 3200S, 3210S
o Adaptec SCSI RAID 3400S, 3410S
o Adaptec SmartRAID PM1554
o Adaptec SmartRAID PM1564
o Adaptec SmartRAID PM2554
o Adaptec SmartRAID PM2564
o Adaptec SmartRAID PM2664
o Adaptec SmartRAID PM2754
o Adaptec SmartRAID PM2865
o Adaptec SmartRAID PM3754
o Adaptec SmartRAID PM3755U2B / SmartRAID V Millennium
o Adaptec SmartRAID PM3757
o DEC KZPCC-AC (LVD 1-ch, 4MB or 16MB cache), DEC KZPCC-CE (LVD 3-ch, 64MB cache), DEC KZPCC-XC (LVD 1-ch, 16MB cache), DEC KZPCC-XE (LVD
3-ch, 64MB cache) -- rebadged SmartRAID V Millennium
FILES
/dev/asr* Adaptec SCSI RAID control nodes
NOTES
The ATA based controllers present their devices as SCSI-like devices via CAM. For IDE drives attached to these cards, a subset of standard
SCSI commands and mode pages are understood via translation performed in the card's firmware.
SEE ALSO
da(4)
HISTORY
The asr (Adaptec SCSI RAID) driver first appeared as the dpti2o driver under BSDi BSD/OS 3.2, then under FreeBSD 2.2.8 and was ported over to
the CAM layer represented in 4.0.
AUTHORS
The asr driver was kindly donated by Adaptec and is maintained by Mark Salyzyn <mark_salyzyn@adaptec.com>. This manual page was written by
Mark Salyzyn and fixed up by Jeroen Ruigrok van der Werven <asmodai@FreeBSD.org>.
BSD
July 14, 2004 BSD