Sponsored Content
Operating Systems Solaris How to install Sun Solaris 10 inside VMware Workstation 5.5 Post 302072121 by thunderfastfox on Thursday 27th of April 2006 05:59:13 PM
Old 04-27-2006
Cool

Thx thats cool Smilie
 

10 More Discussions You Might Find Interesting

1. Solaris

Solaris 10 on Sun W2100z workstation?

I am looking to buy W2100z workstation. I want to run solaris 10 on it. I realize it's a few years old, from 2004. Is it a good machine to get or should I look for a newer workstation? (1 Reply)
Discussion started by: etc
1 Replies

2. Solaris

cant setup network Sun Solaris 10 on Vmware

Hi all, I have install sun solaris 10 on vmware server and i cant ping the solaris guest machine from the host and vice versa. The enable network card in the host machine is an wifi card so I know that i can't use bridged network from Vmware. I tried to use host or NAT but it seem not to work... (1 Reply)
Discussion started by: papiseckfr
1 Replies

3. Solaris

Adding new Hdd in sun 10 with vmware workstation

hi, i am using vmware workstation 6.0 and i installed sun solaris 10. when i add new hard disk(vm->>settings->>add). when i start the system and try to use format command there i only see my old one hdd (new added hdd is not showing). but my new hdd is showing at the bottom right as a icon where... (2 Replies)
Discussion started by: Anand15880
2 Replies

4. Solaris

Ping Sun Solaris 10 on VmWare

Hi, i installed Sun Solaris 10 on VmWare Workstation 6.5 on my Windwos Vista PC. I would to ping solaris virtual machin froma my pc, but i can't do that. Can help me?! I'm sorry for my bad English. akela87 (2 Replies)
Discussion started by: akela87
2 Replies

5. Solaris

Error opening PAM libraries : solaris 10 on vmware workstation

Hi Admins, I am facing an issue with Solaris 10 sitting on vmware workstation... When I start it, it gives me an error : "Error opening PAM libraries, contact system administrator" Also I can reach it via putty, but none of the id/passwd working. I did revert pam.conf. But still no... (2 Replies)
Discussion started by: snchaudhari2
2 Replies

6. Solaris

Solaris 10x86 on VMware Workstation

Is it possible to create metadevices and soft partitions using Solaris Volume Manager on Solaris 10 x86 that is running on VMware Workstation. It would a low cost method to practice extending soft partitions and metadevices. If anyone has an experience with this please share. Regards (1 Reply)
Discussion started by: Tirmazi
1 Replies

7. Linux

vmware workstation

i have following :- fedora 16 x 64bit kernel 3.2.7-1 vmware workstation 8.0.2. Steps to install vmware workstation to access ESX machine 1- sh vmware name.bundle 2- setup started and completed with out any warning. 3- when i type "vmware " then "VMware Module Updater Started" and the... (2 Replies)
Discussion started by: engrtahir2007
2 Replies

8. Solaris

Solaris x86 on vmware workstation panic and almost crashing

Hello Admins, Howz it going? Coming to our forum after long time. Well, a solaris x86 system on my vmware workstation is facing a big trouble. I did a file system check on root file system. And after reboot, I am getting an error for both normal mode and fail safe mode. I have... (4 Replies)
Discussion started by: snchaudhari2
4 Replies

9. Solaris

Copy via samba on vmware workstation with Solaris taking much longer than usual

i have a vmware workstation with solaris 10 installed on this. i copying 2 gb data via samba from windows to this vmware workstation. copy speed is 24 kb/sec. how i can speed up this copy process ? (7 Replies)
Discussion started by: rehantayyab82
7 Replies

10. Solaris

Solaris x86 guest in vmware workstation

I swear I have no other devices on the vmnet 192.168.142.2, but after I configured one of the solaris x86 os, I kept getting warning ..node xx xxxxx have our ip addresss 192.168.142.2, and it scrolled thru it forever .. I tried to boot it into single user mode , still having the same issue.. ... (1 Reply)
Discussion started by: ppchu99
1 Replies
WBAR(1) 						      General Commands Manual							   WBAR(1)

NAME
wbar - a light and fast launch bar SYNOPSIS
wbar [options] DESCRIPTION
This manual page documents briefly the wbar command. wbar is a quick launch bar. Its fast, light and cool eye-candy. OPTIONS
A summary of options is included below. --help Show summary of options. -config conf-file Use conf-file as wbar config file. -above-desk Run over a desktop app (ie: xfdesktop). -isize i Set icon size (eg: 32). -idist d Set icon dist (eg: 1). -zoomf z Set zoom factor (eg: 1.8 or 2.5). -jumpf j Set jump factor (eg: 1.0 or 0.0). -pos p Set position. Choose from top, bottom, left, right, center, <bot|top>-<right|left>. -dblclk ms Set ms for double click (0: single click). -bpress Icon gets pressed. -vbar Show vertical bar. -balfa i Set bar alfa (0-100). -falfa i Set unfocused bar alfa (0-100). -filter i Set color filter (0: none 1: hovered 2: others, 3: all). -fc 0xAARRGGBB Set filter color (default green 0xff00c800). -nanim i Set number of animated icons: 1, 3, 5, 7, 9, ... -nofont If set disables font rendering. AUTHOR
wbar was written by Rodolfo Granata <warlock.cc@gmail.com>. This manual page was written by Krzysztof Burghardt <krzysztof@burghardt.pl>, for the Debian project (and may be used by others). March 16, 2009 WBAR(1)
All times are GMT -4. The time now is 03:20 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy