04-27-2006
How to install Sun Solaris 10 inside VMware Workstation 5.5
Some members asked about this way, click
Here
u will find what u want
10 More Discussions You Might Find Interesting
1. Solaris
I am looking to buy W2100z workstation. I want to run solaris 10 on it.
I realize it's a few years old, from 2004.
Is it a good machine to get or should I look for a newer workstation? (1 Reply)
Discussion started by: etc
1 Replies
2. Solaris
Hi all,
I have install sun solaris 10 on vmware server and i cant ping the solaris guest machine from the host and vice versa.
The enable network card in the host machine is an wifi card so I know that i can't use bridged network from Vmware.
I tried to use host or NAT but it seem not to work... (1 Reply)
Discussion started by: papiseckfr
1 Replies
3. Solaris
hi,
i am using vmware workstation 6.0 and i installed sun solaris 10.
when i add new hard disk(vm->>settings->>add).
when i start the system and try to use format command there i only see my old one hdd (new added hdd is not showing). but my new hdd is showing at the bottom right as a icon where... (2 Replies)
Discussion started by: Anand15880
2 Replies
4. Solaris
Hi,
i installed Sun Solaris 10 on VmWare Workstation 6.5 on my Windwos Vista PC. I would to ping solaris virtual machin froma my pc, but i can't do that. Can help me?!
I'm sorry for my bad English.
akela87 (2 Replies)
Discussion started by: akela87
2 Replies
5. Solaris
Hi Admins,
I am facing an issue with Solaris 10 sitting on vmware workstation...
When I start it, it gives me an error : "Error opening PAM libraries, contact system administrator"
Also I can reach it via putty, but none of the id/passwd working.
I did revert pam.conf. But still no... (2 Replies)
Discussion started by: snchaudhari2
2 Replies
6. Solaris
Is it possible to create metadevices and soft partitions using Solaris Volume Manager on Solaris 10 x86 that is running on VMware Workstation.
It would a low cost method to practice extending soft partitions and metadevices.
If anyone has an experience with this please share.
Regards (1 Reply)
Discussion started by: Tirmazi
1 Replies
7. Linux
i have following :-
fedora 16 x 64bit
kernel 3.2.7-1
vmware workstation 8.0.2.
Steps to install vmware workstation to access ESX machine
1- sh vmware name.bundle
2- setup started and completed with out any warning.
3- when i type "vmware " then "VMware Module Updater Started" and the... (2 Replies)
Discussion started by: engrtahir2007
2 Replies
8. Solaris
Hello Admins,
Howz it going?
Coming to our forum after long time.
Well, a solaris x86 system on my vmware workstation is facing a big trouble.
I did a file system check on root file system. And after reboot, I am getting an error for both normal mode and fail safe mode.
I have... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
9. Solaris
i have a vmware workstation with solaris 10 installed on this.
i copying 2 gb data via samba from windows to this vmware workstation.
copy speed is 24 kb/sec.
how i can speed up this copy process ? (7 Replies)
Discussion started by: rehantayyab82
7 Replies
10. Solaris
I swear I have no other devices on the vmnet 192.168.142.2, but after I configured one of the solaris x86 os, I kept getting warning ..node xx xxxxx have our ip addresss 192.168.142.2, and it scrolled thru it forever ..
I tried to boot it into single user mode , still having the same issue..
... (1 Reply)
Discussion started by: ppchu99
1 Replies
LEARN ABOUT REDHAT
httppower
httppower(8) powerman httppower(8)
NAME
httppower - communicate with HTTP based power distribution units
SYNOPSIS
httppower [--url URL]
DESCRIPTION
httppower is a helper program for powerman which enables it to communicate with HTTP based power distribution units. It is run interac-
tively by the powerman daemon.
OPTIONS
-u, --url URL
Set the base URL.
INTERACTIVE COMMANDS
The following commands are accepted at the httppower> prompt:
auth user:pass
Authenticate to the base URL with specified user and password, using ``basic'' HTTP authentication which sends the user and password
over the network in plain text.
seturl URL
Set the base URL. Overrides the command line option.
get [URL-suffix]
Send an HTTP GET to the base URL with the optional URL-suffix appended.
post [URL-suffix] key=val[&key=val]...
Send an HTTP POST to the base URL with the optional URL-suffix appended, and key-value pairs as argument.
FILES
/usr/sbin/httppower
/etc/powerman/powerman.conf
ORIGIN
PowerMan was originally developed by Andrew Uselton on LLNL's Linux clusters. This software is open source and distributed under the terms
of the GNU GPL.
SEE ALSO
powerman(1), powermand(8), httppower(8), plmpower(8), vpcd(8), powerman.conf(5), powerman.dev(5), powerman-devices(7).
http://sourceforge.net/projects/powerman
powerman-2.3.5 2009-02-09 httppower(8)