04-27-2006
The /etc/inittab file is ok.
in /etc/rc.log the content is below.
I've tried to run mountall -m but still stack
Old /etc/rc.log moved to /etc/rc.log.old
**************************************************
HP-UX Start-up in progress
Wed Apr 26 08:25:48 SADT 2006
**************************************************
Configure system crash dumps
Output from "/sbin/rc1.d/S080crashconf start":
----------------------------
EXIT CODE: 0
Mount file systems
Output from "/sbin/rc1.d/S100localmount start":
----------------------------~
~
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
i am currently am planning to start a webserver to host a community of webpages, but i need help getting started? anyone have any sites or advice for me? thanks! (1 Reply)
Discussion started by: bowlofrice
1 Replies
2. IP Networking
Solaris v5.6
how do you stop and start the network services? (4 Replies)
Discussion started by: Westy564
4 Replies
3. Solaris
i have installed solaris 10 on PIII i Ghz cpu,
whole installation carried out in GUI mode but after installation it is unable to start GUI mode.
Error is : "X server can not be started on display 0"
screed flickers twice and the CLI login prompt appears (1 Reply)
Discussion started by: ajays
1 Replies
4. UNIX for Dummies Questions & Answers
Hi There
Kindly inform me on how to start and stop the print services in Unix from the command line. (2 Replies)
Discussion started by: esh
2 Replies
5. Solaris
Hi Gurus
Sorry to ask this question again but left with no option
I have entry in /etc/dfs/dfstab for resources which i am welling to shaer over the netwrok. Idelay once i execute shaerall it should enabel the nfs/server servcie in Solaris 10, however it was not stared and later i tried... (2 Replies)
Discussion started by: kumarmani
2 Replies
6. UNIX for Advanced & Expert Users
Sir,
I have installed an Apache server in Fedora 9 (packages)
and when i go to etc folder and try the command
httpd -k start
it says command not found....can any one help me out!!!
---------- Post updated at 12:02 PM ---------- Previous update was at 11:46 AM ----------
When i... (4 Replies)
Discussion started by: bssandeshbs
4 Replies
7. Solaris
Hi,
I do not get nfs/server started.
bash-3.00# svcadm enable nfs/server
bash-3.00# svcs -a |grep nfs
disabled 21:44:36 svc:/network/nfs/cbd:default
disabled 21:44:36 svc:/network/nfs/client:default
disabled 21:44:51 svc:/network/nfs/rquota:default
disabled ... (4 Replies)
Discussion started by: jld
4 Replies
8. Solaris
hi guys
i try to start my web server on solaris 10 with T2000 server, i have been already start but the status always maintenace. when i check logfile i have this messages
when i exceute " svcs -l http" i have this output
fmri svc:/network/http:apache2
name ... (10 Replies)
Discussion started by: audi_99
10 Replies
9. SCO
Hi all,
I have a customer whose sco unix server wasnt power off correctly and when booting it up I noticed that the boot up takes a while to finish the " Starting TCP services: snmpd routed lpd". after that the server is ready for login, but you cannot ping anything from the server (apart from... (2 Replies)
Discussion started by: CharlL
2 Replies
10. Linux
Hi All,
My application uses three different sub-services to make complete application up and running to normal.
The entry of all the three services are present in /etc/init.d directory with proper softlink created to application home path where it actually exists.
In one rare case one of the... (3 Replies)
Discussion started by: hk_kamozalwar
3 Replies
LEARN ABOUT OSF1
sys_attrs_bparm
sys_attrs_bparm(5) File Formats Manual sys_attrs_bparm(5)
NAME
sys_attrs_bparm - bparm subsystem attributes
DESCRIPTION
This reference page lists and describes attributes for the Boot Parameters (bparm) kernel subsystem. Refer to the sys_attrs(5) reference
page for an introduction to the topic of kernel subsystem attributes.
Identifies the device from which the system was last booted. This attribute corresponds to the console firmware environment vari-
able with the same name. Do not modify this value, which is set when the system boots.
A combination of flags that controls the boot loader and kernel. This attribute corresponds to the console firmware environment
variable with the same name. Values for the variable are: Boot to multiuser mode. By default, the kernel boots to single-user mode.
Enable the kdebug debugger to debug the kernel. By default, kdebug is not enabled in the kernel. Produce full dumps when the system
crashes. By default, partial dumps are produced. Prompt for an alternate kernel and special arguments when the system is booted. By
default, no questions are asked.
Set boot_osflags only at the console prompt or by using the consvar utility.
Identifies the boot device to be used when one is not included in the boot command line. This attribute corresponds to the console
firmware environment variable with the same name. Set bootdef_dev only at the console prompt or by using the consvar utility.
SEE ALSO
Commands: consvar(8)
Others: sys_attrs(5)
System Administration
sys_attrs_bparm(5)