I'm trying to install a tape drive on a compaq SCO OS 505. well I have gone through the mkdev tape comands and what have you yet no luck. when I reboot and do a simple tape rewind it gives me an error no such device etc.etc. IS there a diference in the xct0 and rct0 a the default?
help.. (2 Replies)
Hello. I have Redhat 8.0 on a laptop. Working good.
I wanted to install the tape drive that is physically attached to it. The tape drive worked fine under Windows98SE. It's one of those parallel QIC-80 drives and I confirmed that it is supported by FTape. It appears that FTape might already... (0 Replies)
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Dear All,
I have a tape drive which has worked for offer 3yrs properly on SCO Openserver Release = 3.2v5.0.5. I tried to clean it all invain. I did a fresh installation of unix of the same OS and did the configuration still didn't bear fruits. The tape is a scsi and the configuration is as... (4 Replies)
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
I've recently been tasked with "refurbishing" an HP Proliant ML370 running SCO 5.0...something. This is primarily used for legacy support and is kept on a shelf for safe keeping. The scope of work includes hardware diagnostics and blowing the dust out.
I have run HP diagnostics on the array,... (1 Reply)
Hi,
Using Redhat 5.7. I have Quantum tape drive connected to the server. I am trying to install the Netbackup software. Just wondering how can I see the Quantum is connected to the server. is any command I run to see the tape drive is connected?
I used to work on Solaris, I used to do... (1 Reply)
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
LEARN ABOUT CENTOS
btape
BTAPE(8) Network backup, recovery and verification BTAPE(8)NAME
btape - Bacula's Tape interface test program
SYNOPSIS
btape [options] device-name
DESCRIPTION
This manual page documents briefly the btape command.
OPTIONS
A summary of options is included below.
-? Show summary of options and commands.
-b bootstrap
Specify a bootstrap file.
-c config
Specify configuration file.
-d nn Set debug level to nn.
-p Proceed inspite of I/O errors.
-s No signals (for debugging).
-v Set verbose mode.
COMMANDS
autochanger
test autochanger
bsf backspace file
bsr backspace record
cap list device capabilities
clear clear tape errors
eod go to end of Bacula data for append
eom go to the physical end of medium
fill fill tape, write onto second volume
unfill read filled tape
fsf forward space a file
fsr forward space a record
help print this reference
label write a Bacula label to the tape
load load a tape
quit quit btape
rawfill
use write() to fill tape
readlabel
read and print the Bacula tape label
rectest
test record handling functions
rewind rewind the tape
scan read() tape block by block to EOT and report
scanblocks
Bacula read block by block to EOT and report
status print tape status
test General test Bacula tape functions
weof write an EOF on the tape
wr write a single Bacula block
rr read a single record
rb read a single bacula block
qfill quick fill command
SEE ALSO bscan(1), bextract(1).
AUTHOR
This manual page was written by Jose Luis Tallon <jltallon@adv-solutions.net>.
Kern Sibbald 26 November 2009 BTAPE(8)