Sponsored Content
Full Discussion: IPv6 on Solaris 10
Special Forums IP Networking IPv6 on Solaris 10 Post 302071411 by andryk on Wednesday 19th of April 2006 10:22:10 AM
Old 04-19-2006
Activating ipv6 is not difficult, u just have to reconfigure your system with 'sys-unconfig', try-it it wont break your box Smilie
But before, note down everything related to your current config like hostname, IPv4 address, route, dns and the like as those will be asked again ...
 

9 More Discussions You Might Find Interesting

1. IP Networking

Solaris IPv6

Hi, Anybody who worked with IPv6 on Solaris 8. I want to get rid of IPv6 (Uninstall). Any comments ...ideas...will be highly appreciated. (4 Replies)
Discussion started by: s_aamir
4 Replies

2. Solaris

(Help) IPv6 tunneling over existing IPv4 in Solaris

Hi folks, i hope you'll help me to configure my ipv6 tunnel. First, i create my tunnel in: Hurricane Electric Free IPv6 Tunnel Broker My IP is 83.228.93.34 in HE: ------------------------ Server IPv4 address: 216.66.84.46 Server IPv6 address: 2001:470:1f14:16a::1/64 Client IPv4 address: ... (2 Replies)
Discussion started by: static
2 Replies

3. Solaris

Solaris 19 10/09 ipv6 interface configuration

Hi, anyone has had experience in a static setting an IPv6 interface?, I'm trying accordance with the admin guide (ipv6 network configuration tasks), configure one interface in the server, actually i can do ping to my default gateway and access the Internet in IPv6, the specific point is however,... (3 Replies)
Discussion started by: pabloluja
3 Replies

4. Solaris

checking Solaris 10 DNS server for IPv6

hi, i have a Solaris 10 DNS server, how do you check whether it can support IPv6 networking ? (0 Replies)
Discussion started by: Exposure
0 Replies

5. Solaris

Solaris 11 disable IPv6

I've new installed Solaris 11 on Sparc T4-1. I'd like to disable IPv6 but with no luck. lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 net0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 2 inet... (6 Replies)
Discussion started by: samer.odeh
6 Replies

6. Solaris

IPv6 for Solaris DNS

I have Bind running on a Solaris box that is our main public DNS. Given my very limited knowledge on DNS, I changed a few of the zones in the DNS to be 'dual-stack'. I did it through Webmin, but I know that I can also do it by adding an AAAA-record to the zone file. My question is how can I make... (2 Replies)
Discussion started by: Dardeer
2 Replies

7. HP-UX

Ipv6 on hpux

my problem: i want to change from ipv4 to ipv6 on my home network. On hpux i can assign only address non routable as fe80::1 fe80::3 etc to my lan0 Editing netconf-ipv6 i can assing a routable ipv6 address like fd55:282f:3b98::/48 or 2001:470:26:307:89a0:aba1:f98b:eb3e but only to alias... (0 Replies)
Discussion started by: Linusolaradm1
0 Replies

8. UNIX for Dummies Questions & Answers

Assigning ipv6 to bonding interface - getting old as well as changed ipv6 in ifconfig output

Hi, I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies

9. Solaris

Solaris 10 IPv6

Hello Dears , please I need your support I have Oracle Solaris 10 X86 server please if you can advise how can I add IP v6 on my server and if IPv6 was disabled how can i enable it also how can i add two IP (v4 and v6) on the same interface or I have to add another interface . Thanks in... (1 Reply)
Discussion started by: ttashman
1 Replies
net_protocol_lookup(9F) 				   Kernel Functions for Drivers 				   net_protocol_lookup(9F)

NAME
net_protocol_lookup - locate an implementation of a network layer protocol SYNOPSIS
#include <sys/neti.h> net_data_t net_protocol_lookup(netid_t id, const char *protocol); INTERFACE LEVEL
Solaris DDI specific (Solaris DDI). PARAMETERS
id network instance identifier. family name of the network protocol to find. DESCRIPTION
The net_protocol_lookup() function attempts to locate a data structure that defines what capabilities it is exporting through this inter- face. The value returned by this call is guaranteed to be valid until it is passed into a call to net_protocol_release(9F), after which it should no longer be treated as valid. The protocol must be a registered name of a network protocol that has been registered. The symbols NHF_INET and NHF_INET6 should be passed to net_protocol_lookup() as the protocol name to gain access to either IPv4 or IPv6 respectively. RETURN VALUES
The net_protocol_lookup() function returns NULL if it does not find any knowledge about the network protocol referenced. Otherwise, it returns a value that can be used with other calls in this framework. CONTEXT
The net_protocol_lookup() function may be called from user, kernel, or interrupt context. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ |Interface Stability |Committed | +-----------------------------+-----------------------------+ SEE ALSO
net_protocol_release(9F), attributes(5) SunOS 5.11 1 May 2008 net_protocol_lookup(9F)
All times are GMT -4. The time now is 02:51 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy