04-11-2006
You don't need a script... what about
ifconfig eth0 up
ifconfig eth0 down
Cheers
ZB
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. IP Networking
What are the steps between "ifconfig eth0 UP" and "net_device->open"?
ifconfig eth0 UP =>
ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) =>
????? => what are these steps?
net_device->open
Thanks! (1 Reply)
Discussion started by: samuncle
1 Replies
3. Solaris
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies
4. Solaris
Hi All,
I want to configure network into my system.
i tried following in to configure the interface
to find the name of interface
#prtdiag |grep net
i got following
0 PCI-1 33 1 network-SUNW, hme
then i tried following
#prtconf -v |grep net
network, instance #0 (6 Replies)
Discussion started by: kumarmani
6 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT CENTOS
pppoe-sniff
PPPOE-SNIFF(8) System Manager's Manual PPPOE-SNIFF(8)
NAME
pppoe-sniff - examine network for non-standard PPPoE frames
SYNOPSIS
pppoe-sniff [options]
DESCRIPTION
pppoe-sniff listens for likely-looking PPPoE PADR and session frames and deduces extra options required for pppoe(8) to work.
Some DSL providers seem to use non-standard frame types for PPPoE frames, and/or require a certain value in the Service-Name field. It is
often easier to sniff those values from a machine which can successfully connect rather than try to pry them out of the DSL provider.
To use pppoe-sniff, you need two computers, a DSL modem and an Ethernet hub (not an Ethernet switch.)
If the DSL modem normally connects directly to your computer's Ethernet card, connect it to the "uplink" port on the Ethernet hub. Plug
two computers into normal ports on the hub. On one computer, run whatever software the DSL provider gave you on whatever operating system
the DSL provider supports. On the other computer, run Linux and log in as root.
On the Linux machine, put the Ethernet interface into promiscuous mode and start pppoe-sniff. If the ethernet interface is eth0, for exam-
ple, type these commands:
ifconfig eth0 promisc
pppoe-sniff -I eth0
On the other machine, start your DSL connection as usual. After a short time, pppoe-sniff should print recommendations for the value of
PPPOE_EXTRA. Set this value in /etc/ppp/pppoe.conf. If pppoe-sniff indicates that something special is required in PPPOE_EXTRA, please e-
mail this to pppoe@roaringpenguin.com along with the name of your ISP and the manufacturer and model number of your DSL modem. This infor-
mation will be collated and provided on the PPPoE web page for users who do not have two computers.
After pppoe-sniff finishes (or you stop it if it seems hung), remember to turn off promiscuous mode:
ifconfig eth0 -promisc
OPTIONS
-I interface
The -I option specifies the Ethernet interface to use. Under Linux, it is typically eth0 or eth1. The interface should be "up" and
in promiscuous mode before you start pppoe-sniff.
-V The -V option causes pppoe-sniff to print its version number and exit.
BUGS
pppoe-sniff only works on Linux.
AUTHORS
pppoe-sniff was written by David F. Skoll <dfs@roaringpenguin.com>.
The pppoe home page is http://www.roaringpenguin.com/pppoe/.
SEE ALSO
pppoe-start(8), pppoe-stop(8), pppoe-connect(8), pppd(8), pppoe.conf(5), pppoe(8), pppoe-setup(8), pppoe-status(8), pppoe-server(8), pppoe-
relay(8)
4th Berkeley Distribution 3 July 2000 PPPOE-SNIFF(8)