VxVM:
How to add one more disk into v08 the stripe should change from 7/128 to 8/128
v v08 - ENABLED ACTIVE 8954292224 SELECT v08-01 fsgen
pl v08-01 v08 ENABLED ACTIVE 8954292480 STRIPE 7/128 RW
sd bkpdg35-01 v08-01 bkpdg35 17216 ... (0 Replies)
Previously , i remove the disk by
#vxdg -g testdg -k rmdisk testdg02
But i got error when i -k adddisk
bash-2.03# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online invalid
c0t1d0s2 auto:none ... (1 Reply)
I have a list of LUN ID, my task is to find if disk has been added or not. How do I do that? I have been searching the forum and not able to find answer.
thanks (4 Replies)
Hi,
I have an iSCSI LUN attached to an AIX 5.3 box. It's initial size is 250GB, I just grew it on the SAN to 300GB, but AIX is not seeing the change. Right now I have some processes going and it's eating up the disk space. I need to grow this lun by atleast 30GB otherwise the process with bomb... (5 Replies)
Hi,
I have a SAN LUN of 550 GB created as an ext3 partition of the entire lun and need to make the lun and partition larger... 600 GB
# fdisk -l /dev/sdj
Disk /dev/sdj: 590.5 GB, 590558003200 bytes
255 heads, 63 sectors/track, 71797 cylinders
Units = cylinders of 16065 * 512 = 8225280... (3 Replies)
I have VxVM 5.1 running on Solaris-10. I have to increase a application file-system and storage team gave me a lun. After scanning scsi port by cfgadm, I can see them in format output. I labelled it, but I am not able to see them in "vxdisk list".
I already tried commands -->
vxdctl enable... (4 Replies)
Hello all,
i try to allocate the same LUN to two server (or more in the future)
i use solaris 10, vxvm (vxfs) for data and solaris zones and EMC DMX-4, i try to migrate solaris zones between servers in case of problem.
and this is what i want to do
- affect LUN to srv00124 and srv10155
-... (5 Replies)
Hello all,
So I made a rookie mistake today. I forgot to remove my disk from my disk group, before running the following command:for i in `ioscan -fnN | awk /NO/'{print $3}'`
do
rmsf -H $i
done
I am trying to run the following command, but not having any luck obviously:vxdg -g dgvol1 rmdisk... (0 Replies)
Discussion started by: mrkejames2
0 Replies
LEARN ABOUT HPUX
iobind
iobind(1M)iobind(1M)NAME
iobind - bind a driver to a device
SYNOPSIS
instance]
DESCRIPTION
The command may be used to perform online unbinding of a device LUN hardware path from its current driver and binding a new driver to it.
As part of the binding operation, the specified driver will be bound to the LUN hardware path and also to its corresponding legacy hardware
paths.
The hardware path specified as the argument to the option must be of the form 64000/0x/0x. The driver name specified with the option will
be bound to the LUN and legacy hardware paths. The optional option specifies an instance number to be assigned to the device associated
with the hardware path. If this option is not used, the device will be assigned a new instance number in the new driver's class. The
optional forces the binding to occur at the next reboot if it cannot be done online.
The device must not be in use while the unbind operation is performed. The driver must support online unbinding and binding. If either of
these requirements is false and the option is not given, the user will be asked if the binding can take effect at the next reboot. The
user is given the option to proceed or not.
If a driver supports online unbinding and binding, then after completes, a device will have one of the following software states as shown
by the command:
The specified driver was successfully bound to the hardware path.
The specified driver cannot be used to claim the hardware at
the specified hardware path.
The device at the address is responding, but it is in an
error state.
The device at the specified hardware path is no longer responding.
The specified hardware path is locked. Try again later.
The driver failed.
Options
recognizes the following options:
Force the binding even though a driver does not support online unbinding
and binding or the device is in use. In this case, the binding will take effect at the next reboot.
The LUN hardware path of a device
must be of the form 64000/0x/0x.
The instance number to be assigned to the device.
The name of the driver that the LUN and legacy hardware paths are to be bound to.
RETURN VALUE
Exit values are:
Successful completion.
An error condition occurred.
EXAMPLES
Unbind the driver bound to the device at hardware path and bind the device to Use the default instance number of the driver's class.
Unbind the driver bound to the device at hardware path and bind the device to Assign it the instance number
Do a forced binding. If the driver does not support online binding or the device is busy, the binding will be deferred till next reboot.
WARNINGS
The and commands should not be run at the same time because both commands attempt to bind drivers. In particular, there may be a short
window while will leave a hardware path unbound. If runs during that window, it may bind a different driver to that hardware path. If
this happens, must be executed again to bind the desired driver.
may be executed only by the superuser.
SEE ALSO ioscan(1M), intro(7).
iobind(1M)