03-24-2006
Using the terminology of vxvm, you take some disks and put them together to make a disk group. Then you carve volumes out of the disk group. It sounds like you have increased the size of a disk and you want vxvm to notice the increased size. Short of reinitializing the disk, I'm not sure you can do that. If you can, I feel that it would be one of the "disk" type commands rather than a "volume" type command. I think you're expected to add a disk to the disk group and then increase the volumes.
9 More Discussions You Might Find Interesting
1. Solaris
VxVM:
How to add one more disk into v08 the stripe should change from 7/128 to 8/128
v v08 - ENABLED ACTIVE 8954292224 SELECT v08-01 fsgen
pl v08-01 v08 ENABLED ACTIVE 8954292480 STRIPE 7/128 RW
sd bkpdg35-01 v08-01 bkpdg35 17216 ... (0 Replies)
Discussion started by: geoffry
0 Replies
2. Solaris
Previously , i remove the disk by
#vxdg -g testdg -k rmdisk testdg02
But i got error when i -k adddisk
bash-2.03# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online invalid
c0t1d0s2 auto:none ... (1 Reply)
Discussion started by: waibabe
1 Replies
3. Solaris
I have a list of LUN ID, my task is to find if disk has been added or not. How do I do that? I have been searching the forum and not able to find answer.
thanks (4 Replies)
Discussion started by: uuontario
4 Replies
4. AIX
Hi,
I have an iSCSI LUN attached to an AIX 5.3 box. It's initial size is 250GB, I just grew it on the SAN to 300GB, but AIX is not seeing the change. Right now I have some processes going and it's eating up the disk space. I need to grow this lun by atleast 30GB otherwise the process with bomb... (5 Replies)
Discussion started by: bbbngowc
5 Replies
5. Red Hat
Hi,
I have a SAN LUN of 550 GB created as an ext3 partition of the entire lun and need to make the lun and partition larger... 600 GB
# fdisk -l /dev/sdj
Disk /dev/sdj: 590.5 GB, 590558003200 bytes
255 heads, 63 sectors/track, 71797 cylinders
Units = cylinders of 16065 * 512 = 8225280... (3 Replies)
Discussion started by: jamba1
3 Replies
6. UNIX for Dummies Questions & Answers
how do I know which hdisk from "lsdev -Cc disk" is my LUN on NetApp after zoning from SAN switch?
is it "MPIO other FC SCSI Disk Drive"? (1 Reply)
Discussion started by: malayo
1 Replies
7. Emergency UNIX and Linux Support
I have VxVM 5.1 running on Solaris-10. I have to increase a application file-system and storage team gave me a lun. After scanning scsi port by cfgadm, I can see them in format output. I labelled it, but I am not able to see them in "vxdisk list".
I already tried commands -->
vxdctl enable... (4 Replies)
Discussion started by: solaris_1977
4 Replies
8. Solaris
Hello all,
i try to allocate the same LUN to two server (or more in the future)
i use solaris 10, vxvm (vxfs) for data and solaris zones and EMC DMX-4, i try to migrate solaris zones between servers in case of problem.
and this is what i want to do
- affect LUN to srv00124 and srv10155
-... (5 Replies)
Discussion started by: mat_solaris
5 Replies
9. HP-UX
Hello all,
So I made a rookie mistake today. I forgot to remove my disk from my disk group, before running the following command:for i in `ioscan -fnN | awk /NO/'{print $3}'`
do
rmsf -H $i
done
I am trying to run the following command, but not having any luck obviously:vxdg -g dgvol1 rmdisk... (0 Replies)
Discussion started by: mrkejames2
0 Replies
LEARN ABOUT OSF1
extendfs
extendfs(8) System Manager's Manual extendfs(8)
NAME
extendfs - Extends UFS file systems
SYNOPSIS
/sbin/extendfs [- s] [disk_blocks] device_name
DESCRIPTION
Use the extendfs command to increase the storage space in a UFS file system. The file system must not be mounted when you perform this
operation. To extend a mounted (in use) UFS file system, use the mount command with the -o extend option.
The procedure for increasing the storage space of a UFS file system is as follows: Look at the contents the /etc/fstab file to identify the
disk partition that maps to the file system. Ensure that there is available storage space on the target disk as follows: If LSM is in use
on your system, use LSM commands to increase the size of the LSM volume as described in the Logical Storage Manager guide. If LSM is not
in use on your system, use the disklabel command or the diskconfig graphical user interface to check the current size and use of partitions
on the disk. If there is adequate space on an adjacent partition, use the disklabel command to write the current label to a file as fol-
lows: # disklabel -r dsk4 > d4label Edit the disklabel file to change the size of the partition on which your UFS file system resides.
Increase the number of disk blocks on the partition and decrease the disk block size of the adjacent partition by an equivalent number.
Use the disklabel command with the -R option to write the revised label to the raw disk as follows: # disklabel -R /dev/rdisk/dsk4 d4label
When the disk label is revised, extend the file system using the extendfs command. You can either use the full extent of the newly sized
partition or extend the file system in stages. The following example commands show both methods. To extend the file system to use all the
available space, you specify the disk partition on which the file system resides, as follows: # extendfs /dev/disk/dsk4g To extend the
file system to use only part of the available space, you specify a number of disk blocks, as follows: # extendfs -s 300000 /dev/disk/dsk4g
The remainder of the extended partion is reserved for future use.
You can extend a file system as many times as necessary, up to the physical limit of the storage device. When no more space is available
on the storage device, you must back up the file system using the dump command and restore the file system to a storage device that has
more available space.
Once you have extended a file system, the operation cannot be reversed except by a back up and restore operation. Use the dump command to
back up the file system. You can then reset the partition sizes manually and restore the file system to the storage device.
ERRORS
The disklabel command produces output similar to that of the newfs command. If a list of disk blocks is not displayed on the terminal, the
command has failed. Verify the partition settings and the mount status of the target file system.
The disklabel command does not permit you to overwrite a partition if it is in use. Refer to the disklabel(8) reference page for more
information on label errors.
FILES
Specifies the command path.
RELATED INFORMATION
diskconfig(8), disklabel(8), mount(8), and fstab(4).
extendfs(8)