03-21-2006
Thanks for the explanation. The watchdog-reboot is set to false currently. There is only one CPU in this box. I realize from what you've posted that reloading the software is probably an exercise in futility, but I have a good backup of the config and I really do want to avoid replacing the CPU if at all possible......so I'm going to try the reload just in case.
If the reload fails, I'll replace the CPU. Either way, I'll let you know what ultimately fixes the problem. Thanks again for the input.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
we have a problem with a server UNIX SUN OS 5.7 :
we tried to reboot it and we have the following error message :
"boot load failed
the file just loaded does not appear to be executable "
we booted the server in single user mode with the cdrom
we made the mirrored disk bootable
we tried... (2 Replies)
Discussion started by: farzolito
2 Replies
2. UNIX for Advanced & Expert Users
Hi All.
Yesterday my pc worked fine. Today when booting the sequence gets just past mounting the root filesystem - it then says
' Module dependencies up to date (no new kernel modules found).'
At this point it hangs and goes no further! Does this sound familiar to anyone?
I am running... (2 Replies)
Discussion started by: silvaman
2 Replies
3. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
4. UNIX for Advanced & Expert Users
i have unix 5.4 running on team server hs failing to boot.
when i turn it on, it prints the following lines on the screen and just stops:
module ID 01: (0011) Main power supply ok
module ID 01: (0012) checks ok
module ID 01: (0020) test of SCSI device 0 x 0 in progress
module ID 01:... (4 Replies)
Discussion started by: ronst
4 Replies
5. Solaris
Hi everyone,
I have sun fire280R machine before i it is installed with solaris5.9 now i want to upgrade it but it not booting from the cd rom ....OK prompt also not comming i dont have solaris keyboard to press stop-A key...i have a intel supported keyboard ...what may be the problem it is... (1 Reply)
Discussion started by: alakshmanrao
1 Replies
6. Solaris
In a Solaris9 environment I'm trying to restore flash archive (flar) with SVM mirrored devices to same server via jumpstart server and it is failing to create boot file and drops down to a command prompt in single user mode, metastat -i and metastat -p output looks good when compared to the ones... (0 Replies)
Discussion started by: mbak
0 Replies
7. UNIX for Dummies Questions & Answers
hello
i have a sun server V890 and it stops booting after adding 2 CPUs modules and gives me the following error message:
Enabling system bus....... Done
Initializing CPUs......... Done
Initializing boot memory..
RAM-Copy CRC failure!Can't start: No image found
FATAL: Can't find/decompress... (0 Replies)
Discussion started by: bahjatm
0 Replies
8. Solaris
hello
i have a sun server V890 and it stops booting after adding 2 CPUs modules and gives me the following error message:
Enabling system bus....... Done
Initializing CPUs......... Done
Initializing boot memory..
RAM-Copy CRC failure!Can't start: No image found
FATAL: Can't find/decompress... (12 Replies)
Discussion started by: bahjatm
12 Replies
9. Solaris
Hi all,
I have the the following SCSI diagnostic codes shown in the attached photo
I suspect disk drive failure what can I do further to diagnose the disk. and if possible to boot into OS again. (5 Replies)
Discussion started by: h@foorsa.biz
5 Replies
10. Solaris
Hi
I have a problem on a server, when he boot I have this type of message loop, do you know what it corresponds to ?
( requesting internet Adress for 0:3:ba:fa:33:91 )
Regards
Sun Fire V240, No Keyboard
Copyright 2007 Sun Microsystems, INC. All rights reserved.
openboot 4.22.33,... (10 Replies)
Discussion started by: yoyo-tns
10 Replies
LEARN ABOUT DEBIAN
lmarbles
LMARBLES(6) Games Manual LMARBLES(6)
NAME
lmarbles - build figures out of colored marbles
SYNOPSIS
lmarbles [--version]
DESCRIPTION
You goal in the puzzle game lmarbles is to create a more or less complex figure out of single marbles within a time limit to reach the next
level. Sounds easy? Well, there is a problem: If a marble starts to move, it will not stop until it hits a wall or another marble.
OPTIONS
--version Show version information and exit.
FILES
~/.lgames/lmarbles.conf
Automatically generated configfile. This is not meant for human editing.
/var/games/lmarbles/lmarbles.prfs
Global preferences and score file. Not for human editing.
BUGS
Please report any bugs you find to Michael Speck <kulkanie@gmx.net>.
LICENCE
lmarbles is covered by the GNU General Public License (GPL).
SEE ALSO
barrage(6), lbreakout2(6), lgeneral(6), lpairs(6), ltris(6),
AUTHOR
Michael Speck <kulkanie@gmx.net>
This manual page was written by Uwe Hermann <uwe@hermann-uwe.de>, for the Debian GNU/Linux system (but may be used by others).
December 23, 2007 LMARBLES(6)