03-20-2006
show firmware of network card
hi,
is there a command or way to see which firmware my network card(s) has?
i could imaging that i would see it in the OBP (show-nets; cd /...@../...; .properties) but is there a way to see it in solaris?
Solaris9 (09/05) on a V440 with GigaSwift Ethernet MMF (X4151A) adapters (using ce drivers)
thanks
-PRESSY
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Dummies Questions & Answers
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies
3. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
4. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
5. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
6. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
7. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
8. UNIX for Advanced & Expert Users
Is there a command that display all network info. I'm looking for ip address, subnet mask, gateway, and dns. If there isn't a single command could someone please write me a shellscript that can do this? (8 Replies)
Discussion started by: cokedude
8 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
10. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
LEARN ABOUT DEBIAN
if_cas
CAS(4) BSD Kernel Interfaces Manual CAS(4)
NAME
cas -- Sun Cassini/Cassini+ and National Semiconductor DP83065 Saturn Gigabit Ethernet driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device miibus
device cas
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_cas="YES"
DESCRIPTION
The cas driver provides support for the Sun Cassini/Cassini+ and National Semiconductor DP83065 Saturn Gigabit Ethernet controllers found on-
board in Sun UltraSPARC machines and as add-on cards.
All controllers supported by the cas driver have TCP/UDP checksum offload capability for both receive and transmit, support for the reception
and transmission of extended frames for vlan(4) and an interrupt coalescing/moderation mechanism as well as a 512-bit multicast hash filter.
The cas driver also supports Jumbo Frames (up to 9022 bytes), which can be configured via the interface MTU setting. Selecting an MTU larger
than 1500 bytes with the ifconfig(8) utility configures the adapter to receive and transmit Jumbo Frames.
HARDWARE
The chips supported by the cas driver are:
o National Semiconductor DP83065 Saturn Gigabit Ethernet
o Sun Cassini Gigabit Ethernet
o Sun Cassini+ Gigabit Ethernet
The following add-on cards are known to work with the cas driver at this time:
o Sun GigaSwift Ethernet 1.0 MMF (Cassini Kuheen) (part no. 501-5524)
o Sun GigaSwift Ethernet 1.0 UTP (Cassini) (part no. 501-5902)
o Sun GigaSwift Ethernet UTP (GCS) (part no. 501-6719)
o Sun Quad GigaSwift Ethernet UTP (QGE) (part no. 501-6522)
NOTES
On sparc64 the cas driver respects the local-mac-address? system configuration variable which can be set in the Open Firmware boot monitor
using the setenv command or by eeprom(8). If set to ``false'' (the default), the cas driver will use the system's default MAC address for
all of its devices. If set to ``true'', the unique MAC address of each interface is used if present rather than the system's default MAC
address.
Supported interfaces having their own MAC address include on-board versions on boards equipped with more than one Ethernet interface and all
add-on cards.
SEE ALSO
altq(4), miibus(4), netintro(4), vlan(4), eeprom(8), ifconfig(8)
HISTORY
The cas device driver appeared in FreeBSD 8.0 and FreeBSD 7.3. It is named after the cas driver which first appeared in OpenBSD 4.1 and sup-
ports the same set of controllers but is otherwise unrelated.
AUTHORS
The cas driver was written by Marius Strobl <marius@FreeBSD.org> based on the gem(4) driver.
BSD
May 3, 2010 BSD