10-01-2002
Those netra x1/t1 sucks big time...we fried 2-3 boards on them.
they're cheap but...
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi!
Is it possible to add more ttys in Solaris, like with inittab in Linux? I want to switch between the ttys with Alt F1+F2+F3 .... like Linux does.
How can i do this? (1 Reply)
Discussion started by: donald1111
1 Replies
2. HP-UX
I have been fine adding/removing printers up until this week. Now when I go to add a new remote printer I get "corrupted member file". I go to /etc/lp/member and the byte count on the new printer name is 0. I VI the file and put /dev/null in to make it the correct size and it all looks fine and... (2 Replies)
Discussion started by: astout
2 Replies
3. UNIX for Dummies Questions & Answers
Hey there I am just looking for a way to find a corrupt tar file. I want to write a script to help sift through the 1000's of tar files we go through daily and move any corrupt ones to a different directory structure. Is there an easy way to do this. (4 Replies)
Discussion started by: car2nst2006
4 Replies
4. AIX
Hi Administrators,
I have one issue related to GPFS filesystem. We have bad entries in this file system, which reflects error like
ls: 0653-341 The file <filename> does not exist.
when we give "ls -ltr" on this directory.
So we taken the FS filesystem offline and followed the below steps.
... (6 Replies)
Discussion started by: gauravgarg
6 Replies
5. UNIX for Dummies Questions & Answers
Hello, I am currently dumping 30-40 reports on a Unix folder located here /home/apps/reports/prode/excel
I use K-shell to do this task. In that, I use the gzip command to compress these files. I want to be able to use a tar command to first load the entire directory into one file then gzip that... (2 Replies)
Discussion started by: Pramodini Rode
2 Replies
6. Solaris
Hi
I would like to know one thing while recovering from corrupt /etc/system file.
For that we have to do at ok> boot -a
when system ask for system file we give /dev/null. Could any one tell me what /dev/null value will do in this case.
Regards (1 Reply)
Discussion started by: sb200
1 Replies
7. UNIX for Advanced & Expert Users
We have an issue here:
The libc.so.6 file (link) is corrupted and it causes the system unbootable. It even doesn't boot to single user mode. How can we boot the system to fix the library file? Or is there any other solutions for this issue?
Here are some boot messages:... (6 Replies)
Discussion started by: aixlover
6 Replies
8. UNIX for Dummies Questions & Answers
Today there was a situation where processes running from inittab was broken. Can someone help me understand, how to find out, who might have stopped those processes? Or how does it get broken?
G (2 Replies)
Discussion started by: ggayathri
2 Replies
9. Solaris
I've a tape contains a corrupt tar file. I'm using Unix SunOS 5.5.1. So when I run this command : dd if=/dev/rmt/0 of=/tmp/outputfile.tar
I get this error message :
warning /pci@1f, 0/pci@1/pci@1/sunw, isptwo@4/st@4,0 (sty): Error for command : read Error Level: Fatal Requested... (2 Replies)
Discussion started by: akaderb
2 Replies
TCOM(4) BSD Kernel Interfaces Manual TCOM(4)
NAME
tcom -- multiplexing serial communications interface
SYNOPSIS
For 4-port TC-400 series boards:
tcom0 at isa? port 0x100 irq 5
com2 at tcom? slave ?
com3 at tcom? slave ?
com4 at tcom? slave ?
com5 at tcom? slave ?
For 8-port TC-800 series boards:
tcom0 at isa? port 0x100 irq 5
com2 at tcom? slave ?
com3 at tcom? slave ?
com4 at tcom? slave ?
com5 at tcom? slave ?
com6 at tcom? slave ?
com7 at tcom? slave ?
com8 at tcom? slave ?
com9 at tcom? slave ?
DESCRIPTION
The tcom driver provides support for the Byte Runner Technologies TC-400 and TC-800 series boards that multiplex together up to four or eight
EIA RS-232C (CCITT V.28) communications interfaces.
Each tcom device is the master device for up to eight com devices. The kernel configuration specifies these com devices as slave devices of
the tcom device, as shown in the synopsis. The slave ID given for each com device determines which bit in the interrupt multiplexing regis-
ter is tested to find interrupts for that device. The port specification for the tcom device is used to compute the base addresses for the
com subdevices and the port for the interrupt multiplexing register.
Not all possible configuration options are currently supported (for example, speeds beyond 115200 baud are not currently supported).
FILES
/dev/tty??
SEE ALSO
com(4)
HISTORY
The tcom driver was written by Jukka Marin.
BSD
May 20, 1998 BSD