Sponsored Content
Special Forums IP Networking Quad Fast Ethernet Card on Sparc 10? Post 28916 by croccopollo on Thursday 26th of September 2002 10:23:35 AM
Old 09-26-2002
Hallo to everybody,
Sorry, but I need a quick info about the file to edit on SUN, under /etc to "stick" the info into the config file.
Thank you very much
Bye
EnzoSmilie
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies

2. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies

3. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies

4. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies

5. Solaris

Quad Ethernet

I have a Quad Ethernet card in a 220R. 2 ports activated. Each has its own hostname file and both hostnames are in the hosts file. I want both ports to have the same IP address so we can use the 2nd port in case we lose communication on the port. On bootup, the box gives me: SIOCSLIFFLAGS:... (5 Replies)
Discussion started by: hshapiro
5 Replies

6. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies

7. Solaris

quad card configuration

Hi Group, I Have just installed quad card in my V440 machine, I am facing problem I cn just ping its ce0 card only rest of the cards are not ping able, here is details of my machine. ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 ... (2 Replies)
Discussion started by: sameergrover
2 Replies

8. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies

9. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres (10 Replies)
Discussion started by: andresguillen
10 Replies

10. Hardware

Best hardware for a fast local Ethernet?

Dear all, I am setting up a new Ethernet network at home, I am going to have a good 100 Mbps internet connection (optic fiber) with a modem that have a gigabit ethernet card. I would like to to measure the speed of data transmission between several servers that are going to be connected to the... (2 Replies)
Discussion started by: freddie50
2 Replies
INFO(5) 							File Formats Manual							   INFO(5)

NAME
info - readable online documentation DESCRIPTION
The Info file format is an easily-parsable representation for online documents. It can be read by emacs(1) and info(1) among other pro- grams. Info files are usually created from texinfo(5) sources by makeinfo(1), but can be created from scratch if so desired. For a full description of the Texinfo language and associated tools, please see the Texinfo manual (written in Texinfo itself). Most likely, running this command from your shell: info texinfo or this key sequence from inside Emacs: M-x info RET m texinfo RET will get you there. AVAILABILITY
http://www.gnu.org/software/texinfo/ REPORTING BUGS
Please send bug reports to bug-texinfo@gnu.org, general questions and discussion to help-texinfo@gnu.org. SEE ALSO
info(1), install-info(1), makeinfo(1), texi2dvi(1), texindex(1). emacs(1), tex(1). texinfo(5). FSF
GNU Info INFO(5)
All times are GMT -4. The time now is 06:37 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy