09-21-2002
routing problem
following Problem.
I configured my SuSE Linux 8.0 as a router. I4l, named, ip_forward, iptables (NAT/MASQUERADING) are running or are aktivatet.
I just can get a internet connection about the proxy server squid, but if i want to use other protocols i need functional routing.
(I had this configuration with routing some times before on run, but after reinstalling the system, it dont want to run correctly)
I believe that at my last configuration at the sysstart SETTING UP ROUTING starts. Now it don't start and i cant find a option to aktivate it.
If sombody have a idea, then write.
THX
10 More Discussions You Might Find Interesting
1. IP Networking
Hi
I know this problem is more likely some windows problem but it has also something to do with unix.
We have a windows nt environment wich uses AIX (unix) machines as file servers (samba). In our windows network environment we nicely see al the unix file servers via the 10 MB network. Last... (2 Replies)
Discussion started by: Mark Detrez
2 Replies
2. IP Networking
I have a question concerning networking. Could any forum
members explain to me why I might be getting "no route
to host" messages when I try to connect through ftp and
http protocols?
I have went to my etc/hosts file and everything seems to be
configured properly. I can connect within my... (1 Reply)
Discussion started by: cstovall
1 Replies
3. IP Networking
hi,
below is the situation:
my server is in 128.10.200.xxx network.
i have a solaris computer running in a subnet. this computer got 2 nic card.
1 is 172.18.198.xxx , another 1 is 10.100.xxx.11
there is a machine stick with this computer, ip is 10.100.xxx.12
so, 10.100.xxx.11 and... (3 Replies)
Discussion started by: kyhah
3 Replies
4. IP Networking
Hi,
I am trying to set up the following :
- One linux box connected to the net, static address, eth0
- No other eth interface on the box
I want to set up this box in a way it can accept remote connections, like pptp tunnels (which seems the easier to set up unless you have other idea)... (2 Replies)
Discussion started by: aerostar700
2 Replies
5. Solaris
Hi,
I got problem of Sun Solaris 8 routing.
IP of SunA is 10.16.64.164, and have routing table:
10.16.64.0 10.16.64.164 U 1 19236 bge1
10.6.0.0 10.6.0.3 U 1 16534 bge0
224.0.0.0 10.6.0.3 U 1 ... (4 Replies)
Discussion started by: milo
4 Replies
6. Red Hat
hi,
having an issue on a class C network with trying to get a redhat diskless setup going. I am using oracle enterprise 5, which is RHEL 5.3 i believe.
here is the scenario:
sun sparc m4k that i am planning on making the red hat boxes boot off after i get the network issue fixed.
... (3 Replies)
Discussion started by: caddyjoe77
3 Replies
7. AIX
I need the following solution , please help me...
Current situation
ip: 192.168.0.12 persistent and 192.168.254.12 service ip
gateway: 192.168.0.254
subnet: 255.255.255.0
i have added a new ip on a new nic
ip: 10.10.255.40
gateway: 10.10.255.62
subnet: 255.255.255.224
... (1 Reply)
Discussion started by: rajibimran
1 Replies
8. IP Networking
Internet Gateway
192.168.0.201
Server 1
192.168.0.101
192.168.1.101
192.168.2.101
gateway: 192.168.0.201
VIP: 192.168.1.100
VIP: 192.168.2.100
Server 2
192.168.0.102
192.168.1.102
192.168.2.102
gateway: 192.168.0.201
Client 1
192.168.2.201
gateway: 192.168.2.100 (1 Reply)
Discussion started by: hopfensp
1 Replies
9. Solaris
Hi,
I have two physical interfaces on a servers.
We have connected them to differerent subnets.
1) First interface:
10.158.49.87 to newtwork 10.158.49.0, its gateway is 10.158.49.1
(It is added as default gateway)
It is existing set up. It works well
2) Second interface:
... (1 Reply)
Discussion started by: sri243
1 Replies
10. IP Networking
hi folks,
i have a horstbox-router with the following configuration.
it has 4 ethernet ports from wich one (wan0) is configured as an external modem via dhcp. at this port/interface(wan0) it is connected with my home network (other switch).
this configuration results in the following... (14 Replies)
Discussion started by: gencaslan
14 Replies
LEARN ABOUT REDHAT
atalkd
ATALKD(8) System Manager's Manual ATALKD(8)
NAME
atalkd - AppleTalk RTMP, NBP, ZIP, and AEP manager
SYNOPSIS
/usr/sbin/atalkd [ -f configfile ] [ -1 | -2 ]
DESCRIPTION
atalkd is responsible for all user level AppleTalk network management. This includes routing, name registration and lookup, zone lookup,
and the AppleTalk Echo Protocol (similar to ping(8)). atalkd is typically started at boot time, out of /etc/rc. It first reads from its
configuration file, /etc/atalk//atalkd.conf. If there is no configuration file, atalkd will attempt to configure all available interfaces
and will create a configuration file. The file consists of a series of interfaces, one per line. Lines with `#' in the first column are
ignored, as are blank lines. The syntax is
interface [ -seed ] [ -phase number ] [ -net net-range ] [ -addr address ] [ -zone zonename ] ...
Note that all field except the interface are optional. The loopback interface is configured automatically. If -seed is specified, all
other fields must be present. Also, atalkd will exit during bootstrapping, if a router disagrees with its seed information. If -seed is
not given, all other information may be overriden during auto-configuration. If no -phase option is given, the default phase as given on
the command line is used (the default is 2). If -addr is given and -net is not, a net-range of one is assumed.
The first -zone directive for each interface is the ``default'' zone. Under Phase 1, there is only one zone. Under Phase 2, all routers
on the network are configured with the default zone and must agree. atalkd maps ``*'' to the default zone of the first interface. Note:
The default zone for a machine is determined by the configuration of the local routers; to appear in a non-default zone, each service, e.g.
afpd, must individually specify the desired zone. See also nbp_name(3).
ROUTING
If you are connecting a netatalk router to an existing AppleTalk internet, you should first contact your local network administrators to
obtain appropriate network addresses.
atalkd can provide routing between interfaces by configuring multiple interfaces. Each interface must be assigned a unique net-range
between 1 and 65279 (0 and 65535 are illegal, and addresses between 65280 and 65534 are reserved for startup). It is best to choose the
smallest useful net-range, i.e. if you have three machines on an Ethernet, don't chose a net-range of 1000-2000. Each net-range may have
an arbitrary list of zones associated with it.
EXAMPLE
Below is an example configuration file for a sun4/40. The machine has two interfaces, ``le0'' and ``le1''. The ``le0'' interface is con-
figured automatically from other routers on the network. The machine is the only router for the ``le1'' interface.
le0
le1 -seed -net 9461-9471 -zone netatalk -zone Argus
atalkd automatically acts as a router if there is more than one interface.
FILES
/etc/atalk//atalkd.conf configuration file
BUGS
On some systems, atalkd can not be restarted.
netatalk 1.3 17 Nov 1995 ATALKD(8)