Sponsored Content
Special Forums IP Networking Solaris 9 Ethernet Card Problems Post 27260 by saucierm on Thursday 29th of August 2002 08:55:41 AM
Old 08-29-2002
Solaris 9 Ethernet Card Problems

I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS.
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies

2. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies

3. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies

4. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies

5. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies

6. Solaris

Ethernet card drivers issue...

I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do? Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies

7. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies

8. Linux

Offload parameters for Ethernet Card

Hi, Actually i want to see Offload parameter for my Eth card. Then after i try using this command Anybody can explain ? Is there any problem with my eth card ? (1 Reply)
Discussion started by: justbow
1 Replies

9. Solaris

solaris ethernet card and mounting usb drives

I had installed soalris 10 on my dell vostro 1400.It had installed succefully. If i type ifconfig -a it is showing only my loop back adpater. So how to tell me how to mount my usb drive and how to configure my lan ethernet card,My lan ethernet card is Broadcom. Tell me step... (1 Reply)
Discussion started by: testerindia25
1 Replies

10. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
IFCONFIG(8)						      System Manager's Manual						       IFCONFIG(8)

NAME
ifconfig - configure a TCP/IP device SYNOPSIS
ifconfig [-I ip-device] [-h ipaddr] [-n netmask] [-iv] DESCRIPTION
Ifconfig initializes a TCP/IP device setting the IP address and/or netmask. It will report the address and netmask set. This command may be used if the system has not been configured properly yet. It is only used at boot time to set a fixed address for a system without a physical ethernet. Normally the inet task will find it out by itself from the RARP server. OPTIONS
-h The decimal TCP/IP address to set. -n The netmask to set. -i Don't set the IP address or netmask if already set. This way ifconfig cannot interfere if the numbers have been found out by RARP. -v Report IP address and netmask. This is the default action if there are no other options. SEE ALSO
hostaddr(1), rarpd(8), set_net_default(8), boot(8). AUTHOR
Kees J. Bot (kjb@cs.vu.nl) IFCONFIG(8)
All times are GMT -4. The time now is 12:58 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy