08-22-2002
ifconfig -a on Solaris would give you the following type of info - to get the same on HP-UX you would have to do ifconfig lan1 (or specific interface - gather that info from lanscan)
$ ifconfig -a
hme0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 1
inet 10.14.6.6 netmask fffffc00 broadcast 10.14.6.255
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 2
inet 127.0.0.1 netmask ff000000
On HP-UX:
$ lanscan
Hardware Station Crd Hdw Net-Interface NM MAC HP-DLPI DLPI
Path Address In# State NamePPA ID Type Support Mjr#
8/4/2/0 0x0060B0F93BA9 1 UP lan1 snap1 1 ETHER Yes 119
$ ifconfig lan1
lan1: flags=843<UP,BROADCAST,RUNNING,MULTICAST>
inet 10.14.8.2 netmask fffffc00 broadcast 10.14.8.255
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I recently encountered this on the AIX system
df command showed usage is 100% i.e 1.5 GB while du command showed usage is only 500MB
Why are the 2 commands showing different output
This command shows usage is 1.5 GB
nlxdsm29:deqadm 24> df -k .
/usr/sap/DEQ ... (3 Replies)
Discussion started by: ameya_joshi
3 Replies
2. UNIX for Dummies Questions & Answers
Hello,
I'm running the ls command on an HP-UX 11i platform and am getting skewed listings. In other words, I see 3 columns of perfectly aligned file names, except 1 file is shifted by 2 or 3 bytes. The file to the immediate left of it seems to be causing the problem, for when I do an ls on... (1 Reply)
Discussion started by: bsp18974
1 Replies
3. UNIX and Linux Applications
Hi all,
I'm very new to unix, I'm developing an application in Java, part of which requires me to check if a certain application is still running. In windows, I just use tasklist - if the application has been shut down it won't appear in the task list. I've been trying to use the ps command to... (0 Replies)
Discussion started by: ekatmcg
0 Replies
4. Solaris
Hello folks,
uptime command not shows how long the system has been up.
I know it come from a corruption of /var/adm/utmpx file.
I've done :
cat /dev/null > /var/adm/utmpx
Now who and last commands work fine. But uptime still give me back an answer without the "up time".
In which... (6 Replies)
Discussion started by: gogol_bordello
6 Replies
5. Shell Programming and Scripting
Hi,
I have an command which find the files modified within last 8 days and then after selecting the files from the location it make the tar format and send it to the specified destination ...now I want that this task to be automative ..that is it should happen after every 5 minutes ...for that... (3 Replies)
Discussion started by: NARESH SAXENA
3 Replies
6. Shell Programming and Scripting
Hi All
I am trying to run a script in linux wherein i have a command like this
grep ^prmAttunityUser= djpHewr2XFMAttunitySetup_ae1_tmp
djpHewr2XFMAttunitySetup_ae1_tmp is a temporary file in which the user value is stored but this command in the script returns me balnk value whereas it has a... (4 Replies)
Discussion started by: vee_789
4 Replies
7. Solaris
Hello,
running into a bind when im inputting the following command:
bash-3.00$ ps -p 874 -L -o pid,psr,pcpu
PID PSR %CPU
874 - 0.0
874 - 0.2
874 - 0.0
874 - 1.1
874 - 0.2
Now when i run it on my other SUN machine i get this:
bash-3.00$ ps -p 3874... (0 Replies)
Discussion started by: Nolph
0 Replies
8. Shell Programming and Scripting
I am using HP-UX,KSH
$ jobs -l
+ 19377 Running nohup ksh cat_Duplicate_Records_Removal.ksh </dev/null >/dev/null 2>&1 &
$ ps -p 19377 -fl
F S UID PID PPID C PRI NI ADDR SZ WCHAN STIME TTY TIME COMD
401 S catmgr 19377 19491 ... (1 Reply)
Discussion started by: TomG
1 Replies
9. Shell Programming and Scripting
F S UID PID PPID C PRI NI ADDR SZ WCHAN STIME TTY TIME COMD
401 S catmgr 5748 5742 0 154 20 e0000006d48cd080 133 e0000003fb6e7200 11:22:32 ? 0:00 /opt/ssh/libexec/sftp-server
3401 R catmgr 5742 5631 0 152 20 e0000005f974fa00 750 ... (4 Replies)
Discussion started by: TomG
4 Replies
10. UNIX for Dummies Questions & Answers
Hi Folks,
I have a situation here, where no command is giving any output, and it's not even showing any error message also.
What could be the reason? (3 Replies)
Discussion started by: nixhead
3 Replies
GRE(4) BSD Kernel Interfaces Manual GRE(4)
NAME
gre -- encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated datagrams are routed to a destination host, where
they are decapsulated and further routed to their final destination. The ``tunnel'' appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram and a GRE header. The GRE header specifies the
type of the encapsulated datagram and thus allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on Cisco
routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
/
/
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1, while router B has external address B and internal
address 192.168.2.1, the following commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco routers. This may not be an optimal value, depending
on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8) variable to non-zero.
SEE ALSO
gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a different key or without a key will be treated as
if they would belong to this interface.
The sequence number field also used only for outgoing packets.
BSD
November 7, 2014 BSD