Sponsored Content
Full Discussion: Installing network card
Top Forums UNIX for Dummies Questions & Answers Installing network card Post 26554 by gops on Tuesday 20th of August 2002 01:55:02 PM
Old 08-20-2002
Installing network card

1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out.
 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

3. UNIX for Advanced & Expert Users

network card problem

hi, everyone: alpha 600 au true64 Unix 4.0f my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages. "tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies

4. Solaris

Installing RT2500 Wireless network card

I need to install a driver for my RT2500 PCI wireless network card on my Solaris 10. So I went to the ralink website (the manufacturer of the network card), and downloaded the linux (well supposedly the unix driver) binary file. Burned it to dvd, and copied from the dvd to my solaris computer.... (3 Replies)
Discussion started by: Xannen
3 Replies

5. UNIX for Dummies Questions & Answers

installing scsi card

i hava bought scsi card for taking backup in a 12/24 DAT DRIVE -scounix5.05 i am havaing the cd of the same contain driver files how should i install it. can anybody help me. (0 Replies)
Discussion started by: tatacoffee
0 Replies

6. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

7. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies

8. UNIX for Dummies Questions & Answers

How to install a network card

Hey guys, Sorry, this question might look stupid but I have no idea how to install a network card. My server is a Dell PowerEdge T105 with Debian 5.0 Lenny. My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express. I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies

9. Solaris

Network Card Name details

Hi All, Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ? This is such a basic question which i always overlooked :( Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies

10. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
DAIC(4) 						   BSD Kernel Interfaces Manual 						   DAIC(4)

NAME
daic -- isdn4bsd driver for EICON.Diehl active ISDN cards SYNOPSIS
daic0 at isa? iomem 0xd8000 irq 10 DESCRIPTION
The daic driver supports the old Diehl active cards: S, SX, SXn, SCOM and QUADRO. For a QUADRO card, the driver will detect the board type and use all four ports, each attached as a controller of its own to the isdn4bsd system, which can be listed using the daicctl utility. The daic driver interfaces the ISDN card to the ISDN4BSD kernel subsystem. All lower layer ISDN control is handled by the card. This should allow you to run any national ISDN protocol delivered by EICON.Diehl for your card, but the driver has only been tested with the DSS1 proto- col and some parts of the cards interface are ISDN protocol dependent. The daic driver is written to conform to the software interface documented by Diehl in their ISDN-Karten Benutzerhandbuch from 1992. MICROCODE DOWNLOAD
Every active card needs its own operating software before it can work. You have to download this to the card before using it with isdn4bsd. Use the daicctl utility to do this, i.e. call daicctl -d te_etsi.sx 1 to download the file te_etsi.sx to controller number 1. Use daicctl -l to list all available controllers (and ports). You have to select the correct ISDN protocol file for your ISDN interface, see the Diehl docu- mentation for details. The cards bootstrap process involves another file, which is independent of the card type you use and the protocol you run. It is called download.bin in current versions of the Diehl software distribution and has to be copied to the kernel compile directory under dev/microcode/daic and converted into a header file used when compiling the kernel by running make in that directory. Your kernel compile will fail and remind you of this if you forget to do this. Due to copyright restrictions we cannot distribute the driver with this file inte- grated. But if you own a card, you do have the file (or can get it from the Diehl web server). SEE ALSO
daicctl(1) BUGS
The driver is not yet finished. BSD
January 30, 1998 BSD
All times are GMT -4. The time now is 10:02 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy