|
|
Sponsored Content
Special Forums
Hardware
Filesystems, Disks and Memory
Booting Slackware 8.1
Post 25917 by Rufus330Ci on Wednesday 7th of August 2002 02:01:54 PM
08-07-2002
Booting Slackware 8.1
Hello everyone I just joined this forum 
I used to use Mandrake for the longest time but now I moved over to Slackware 8.1 a couple nights ago
I have 3 main problems.
1) I can't boot up without the boot floppy
2) mouse doesn't work in startX and I don't know the XConfigurator command for Slackware
3) I can't telnet to my new linux box. I can ping it, i can ping 127.. on the linux box and I can get on the net with lynx.
Any help with theses three problems I would greatly appreciate.
Here is the post I made on LinuxQuestions.com on my problem
-------------------
Hello everyone this is my first post :O)
I used to use Mandrake 8.0 for the longest time but I've decided to try out Slackware 8.1. I have it all installed but I have 3 problems.
1) Have to boot off diskette... I have 3 partitions on my 2.7GB drive /dev/hda1 64MB Linux Swap (SELECTED AS BOOTABLE)
/dev/hda2 400MB Linux Extended
/dev/hda5 2.3GB Linux
The install made theses.....
I tried changing the hda5 to be bootable only and together with hda1 and they both needed the boot diskette... I think i might not have this initial setup right with kernels and all. Please help me on this. Maybe some commands or the lilo file i need to make or point to kernel.
2) Mouse doesn't work in startX -- I dont think the keyboard is working either once I go to startX...I have to reboot after typing startx and it fully loads. I can't change scroll lock so I'm pretty sure the keyboard doesn't work. It doesn't lock up though because the clock changes in KDE 3.0
3) I can get on the internet with lynx on the local system, but I can't telnet to my linux box. I had this working with mandrake... commands are different in slackware so I don't have a really good step by step, but the 3Com is being recognized and I have the 192.168... in etc/hosts and my cable router is pointing to that 192 for port 20,21,23,10000.
Any help would be greatly appreciated I want to try to knock out theses problems one at a time so I can get started on my Samba setup next ;O)
Ohh yeah one last thing. The motd file how do I make it so it doesn't reset itself on bootup?!?!
here's my lilo.conf
LILO.CONF in /etc/lilo.conf (I made this from the example lilo.conf-sample)
boot = /dev/hda (I had hda5 here but that didn't work either)
map = /boot/.map
lba32
install = /boot/boot-menu.b
prompt
timeout=150
delay=30
read-only
serial=0,9600
loader=/boot/chain.b
disk=/dev/hda bios=0x80
disk=/dev/hdb bios=0x81
disk=/dev/hdc bios=0x82
disk=/dev/sda bios=0x83
image=/dd/boot/vmlinuz-2.4.2
label=2.4.2
root=current
append="reboot=warm"
then i got windoze,backup kernels...
other=/dev/hda
label=MBR
DF produces
FILESYSTEM 1k-blocks USED AVAILABLE Use% Mounted on
/dev/hda5 2390864 1769864 621000 75% /
When i installed this was confusing i didn't make a /,/home, or /usr
it automatically made a linux swap (hda1) ,linux (hda5), and linux extended (hda2) and the swap is marked as bootable in fdisk...
with this df does this means my linux extended hda2 is not even being used?? its 400mb and I would like to put it to good use.
Thanks for the help in advance, any comments to get this thing booted up except on diskette would be appreciated. Oh yeah when i boot it up without the disk it says PRESS ANY KEY TO REBOOT.
I used to use Mandrake for the longest time but now I moved over to Slackware 8.1 a couple nights ago
I have 3 main problems.
1) I can't boot up without the boot floppy
2) mouse doesn't work in startX and I don't know the XConfigurator command for Slackware
3) I can't telnet to my new linux box. I can ping it, i can ping 127.. on the linux box and I can get on the net with lynx.
Any help with theses three problems I would greatly appreciate.
Here is the post I made on LinuxQuestions.com on my problem
-------------------
Hello everyone this is my first post :O)
I used to use Mandrake 8.0 for the longest time but I've decided to try out Slackware 8.1. I have it all installed but I have 3 problems.
1) Have to boot off diskette... I have 3 partitions on my 2.7GB drive /dev/hda1 64MB Linux Swap (SELECTED AS BOOTABLE)
/dev/hda2 400MB Linux Extended
/dev/hda5 2.3GB Linux
The install made theses.....
I tried changing the hda5 to be bootable only and together with hda1 and they both needed the boot diskette... I think i might not have this initial setup right with kernels and all. Please help me on this. Maybe some commands or the lilo file i need to make or point to kernel.
2) Mouse doesn't work in startX -- I dont think the keyboard is working either once I go to startX...I have to reboot after typing startx and it fully loads. I can't change scroll lock so I'm pretty sure the keyboard doesn't work. It doesn't lock up though because the clock changes in KDE 3.0
3) I can get on the internet with lynx on the local system, but I can't telnet to my linux box. I had this working with mandrake... commands are different in slackware so I don't have a really good step by step, but the 3Com is being recognized and I have the 192.168... in etc/hosts and my cable router is pointing to that 192 for port 20,21,23,10000.
Any help would be greatly appreciated I want to try to knock out theses problems one at a time so I can get started on my Samba setup next ;O)
Ohh yeah one last thing. The motd file how do I make it so it doesn't reset itself on bootup?!?!
here's my lilo.conf
LILO.CONF in /etc/lilo.conf (I made this from the example lilo.conf-sample)
boot = /dev/hda (I had hda5 here but that didn't work either)
map = /boot/.map
lba32
install = /boot/boot-menu.b
prompt
timeout=150
delay=30
read-only
serial=0,9600
loader=/boot/chain.b
disk=/dev/hda bios=0x80
disk=/dev/hdb bios=0x81
disk=/dev/hdc bios=0x82
disk=/dev/sda bios=0x83
image=/dd/boot/vmlinuz-2.4.2
label=2.4.2
root=current
append="reboot=warm"
then i got windoze,backup kernels...
other=/dev/hda
label=MBR
DF produces
FILESYSTEM 1k-blocks USED AVAILABLE Use% Mounted on
/dev/hda5 2390864 1769864 621000 75% /
When i installed this was confusing i didn't make a /,/home, or /usr
it automatically made a linux swap (hda1) ,linux (hda5), and linux extended (hda2) and the swap is marked as bootable in fdisk...
with this df does this means my linux extended hda2 is not even being used?? its 400mb and I would like to put it to good use.
Thanks for the help in advance, any comments to get this thing booted up except on diskette would be appreciated. Oh yeah when i boot it up without the disk it says PRESS ANY KEY TO REBOOT.
|
|
3 More Discussions You Might Find Interesting
1. Slackware
Hi. I'm glad join the unix.com forums.
Here is my first problem:
I've installed Slackware 13 on my PC and configured the IP, Mask and the default gateway.
But now I cannot edit the resolv.conf correctly.
Can you give me an example with DNS servers like 4.4.4.2 ; 4.4.4.4 ; 8.8.4.4 and... (1 Reply)
Discussion started by: intelfan
1 Replies
2. Slackware
I want to know more about the Concurrency(Process Synchronization, Deadlocks) of a slackware, i know already the Concurrency but i want to know further what else is the Concurrency(Process Synchronization, Deadlocks) of a slackware. :cool: (1 Reply)
Discussion started by: green12
1 Replies
3. Slackware
Hello everyone. I am a newbie in operating systems. so far I've been playing with Ubuntu and I like it a lot. I heard about Slackware and I wanna try it. Last night I download the iso but It didn't fit in my usb or Dvd. it is a 4.2 GB. Is there one less than 4.2GB that will fit in my usb or DVD? ... (1 Reply)
Discussion started by: openation1
1 Replies
LEARN ABOUT DEBIAN
ibv_uc_pingpong
IBV_UC_PINGPONG(1) USER COMMANDS IBV_UC_PINGPONG(1) NAME
ibv_uc_pingpong - simple InfiniBand UC transport test SYNOPSIS
ibv_uc_pingpong [-p port] [-d device] [-i ib port] [-s size] [-r rx depth] [-n iters] [-l sl] [-e] HOSTNAME ibv_uc_pingpong [-p port] [-d device] [-i ib port] [-s size] [-r rx depth] [-n iters] [-l sl] [-e] DESCRIPTION
Run a simple ping-pong test over InfiniBand via the reliable connected (RC) transport. OPTIONS
-p, --port=PORT use TCP port PORT for initial synchronization (default 18515) -d, --ib-dev=DEVICE use IB device DEVICE (default first device found) -i, --ib-port=PORT use IB port PORT (default port 1) -s, --size=SIZE ping-pong messages of size SIZE (default 4096) -r, --rx-depth=DEPTH post DEPTH receives at a time (default 1000) -n, --iters=ITERS perform ITERS message exchanges (default 1000) -l, --sl=SL use SL as the service level value of the QP (default 0) -e, --events sleep while waiting for work completion events (default is to poll for completions) SEE ALSO
ibv_rc_pingpong(1), ibv_ud_pingpong(1), ibv_srq_pingpong(1) AUTHORS
Roland Dreier <rolandd@cisco.com> BUGS
The network synchronization between client and server instances is weak, and does not prevent incompatible options from being used on the two instances. The method used for retrieving work completions is not strictly correct, and race conditions may cause failures on some systems. libibverbs August 30, 2005 IBV_UC_PINGPONG(1)