07-21-2002
Do a boot -svr at the ok prompt. It will boot in single user mode and reconfig you scsi drives. it's just like plug and play but only on Unix.
7 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi,
I tried to install Magneto-Optical (MO) drive Fujutsu to COMPAQ Proliant ML350 with SCO Openserver 5.0.5. Harddisk and MO are connected to Adaptec UW-SCSI-3 (driver ad160).
During boot process system shows me that MO is connected to host adapter 1, bus 0, SCSI ID 1 and LUN 0. But when I... (2 Replies)
Discussion started by: yurist
2 Replies
2. AIX
Hi guys,
I have not connected optical cable to the Dual port HBA before. My integrator used to do that for me all the time. Can someone explain to me how can I physically connect optical cable to the HBA port in P570.
The optical cable has two connectors and right now the HBA port has just a... (7 Replies)
Discussion started by: solaix14
7 Replies
3. UNIX for Dummies Questions & Answers
We are trying to make duplicates of some Magneto Optical Disks that were created in Irix 6.5. The disks are 2.3 gig and the using a scsi MOD drive. Is there possbily a disk copy like in dos or some simple script to do this - any help appreciated.
Thanks (0 Replies)
Discussion started by: drew_holm
0 Replies
4. Red Hat
hello,
someone gave me a set of electronic gadgets 'Brookstone' which has mini optical mouse. This mouse label doesn't have model or etc. Mouse does not work properly i.e. pointer is moving right but left/right buttons work opposite and not always could open or close controls.
I suggest it might... (3 Replies)
Discussion started by: susja
3 Replies
5. Solaris
I have installed Solaris 11 Express on my computer and set up a script to make daily snapshots of all filesystems and send them to a backup disc.
Now I'm trying to replace the system disc using a set of captured snapshots. I have found an article on that topic on the internet and have been... (6 Replies)
Discussion started by: RychnD
6 Replies
6. AIX
Hi
My P6 server is with dual vio servers. From the below output we could see that cd devices(cd0 and cd1) has been mapped to the vio client named prdsapfi1.
When we execute "lsdev -Cc cdrom" in prdsapfi1 there are 2 cd devices named cd0 and cd1 showing up in available state.
... (1 Reply)
Discussion started by: newtoaixos
1 Replies
7. Hardware
I have a Dell XPS M1330 laptop. The OS is Windows 10. I had to replace the motherboard because it was bad. After replacing the motherboard I noticed the optical (DVD/CD) drive is neither detected in BIOS and OS nor making any noise at all. Everything else seems to be working fine. The optical drive... (3 Replies)
Discussion started by: milhan
3 Replies
LEARN ABOUT OSF1
sys_attrs_bparm
sys_attrs_bparm(5) File Formats Manual sys_attrs_bparm(5)
NAME
sys_attrs_bparm - bparm subsystem attributes
DESCRIPTION
This reference page lists and describes attributes for the Boot Parameters (bparm) kernel subsystem. Refer to the sys_attrs(5) reference
page for an introduction to the topic of kernel subsystem attributes.
Identifies the device from which the system was last booted. This attribute corresponds to the console firmware environment vari-
able with the same name. Do not modify this value, which is set when the system boots.
A combination of flags that controls the boot loader and kernel. This attribute corresponds to the console firmware environment
variable with the same name. Values for the variable are: Boot to multiuser mode. By default, the kernel boots to single-user mode.
Enable the kdebug debugger to debug the kernel. By default, kdebug is not enabled in the kernel. Produce full dumps when the system
crashes. By default, partial dumps are produced. Prompt for an alternate kernel and special arguments when the system is booted. By
default, no questions are asked.
Set boot_osflags only at the console prompt or by using the consvar utility.
Identifies the boot device to be used when one is not included in the boot command line. This attribute corresponds to the console
firmware environment variable with the same name. Set bootdef_dev only at the console prompt or by using the consvar utility.
SEE ALSO
Commands: consvar(8)
Others: sys_attrs(5)
System Administration
sys_attrs_bparm(5)